Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
I'm trying to replicate an Arduino Uno application where we connect a M3Q alcohol sensor into an analog pin and feed the data into the ADC. The specific board I have is made...
Hello,
sd_softdevice_enable falls in hardfault. I have no 32.768 KHz crystal but is set lfclk with NRF_CLOCK_LFCLKSRC_SYNTH_250_PPM.
I'm running my application on a...
HI,ALL,
i want to try to developer with bluetooth develop studio,which developered by BlueSIG.
i now download the BDS and the PLUGIN for the nordic NRF51.
is there...
Hello,
Does the S120 have support to know on which advertising channel it received an advertisment? Or some kind of feedback to know on which channel the S120 device is...
Hi,
Does anyone know the event end point addresses for the following on the nrf52832:
RADIO_EVENTS->ADDRESS
RADIO_EVENTS->READY
RADIO_EVENTS->END
The addresses for...
Hello guys ,
We developed a product that using a nRF51xx chip and now we are preparing for mass production.
The antenna was designed on PCB and for PCB we are using FR4...
There is a minor issue with the app_fifo library included with nRF5_SDK_11.0.0-2.alpha_bc3f6a0. If the app_fifo_write function is called with the parameter p_size set to 0...
Hi
I am planning to use NRF51822. Have not used these parts yet.
I have 4 peripherals and 1 central hub. All communicating in BLE. And central hub will also connect to...
In our project we are using the nrf51822. We planned to connect an external flash for storage purposes. While coding the software I got the advice to give special attention...
Hi,
I use nRF51822.
Can it judge a UID of higher RSSI level by comparing the RSSI of two advertizers with Central mode in nRF51882?
I want to know a UID of advertiser...
Hi, I use
nRF51822 Rev.3, SDK 7.2, SDK 10.0, S110 8.0, and S120 2.1 most of the time.
I mostly quote most of the codes from the SDK's examples such as HID keyboard or...
Hi all,
We have a issues with the SPI communication and hope someone could help us.
Using SDK 8.0.0 and Soft Device S110 8.0.0
code process step:
enable ble...
Hi
I am investigating some weird issue where a device sometimes locks up: it is BLE connected to my iphone app, and then I bombard it with writes to a specific characteristic...
Hi everyone,
We are on the lookout for a bluetooth module from Nordic that is suitable for our product. The product is a handheld digital stethoscope that transfers acquired...
I am building my application up on the ant_scalable_encrypted_tx example. I want to use RTC too, for that I took an example code off of the rtc example.
The problem is...
