Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
I have a custom board with an nRF52840 that uses high-voltage mode (5V on VDDH) and the chips internal voltage regulators. This requires setting REGOUT0 to 3.3V. My firmware...
Dear Nordic Team,
We are using nRF52840 based module and using its ZigBee Radio. For one certification purpose, we need to know the max. pulse time (duration) for Tx and...
Hi again,
This is my project:
I have 3 nrf52832 kit and a Android phone. I want use my phone to control leds on those 3 boards. Because the phone dont support mesh, so...
Hi, I'm using nrf connect SDK v1.5.0 and I use SES to build and flash projects.
I use Visual Studio Code for only code editing environment. When I was using nrf5 SDK, I...
Hi ! I'm trying to access the beginning of a packet that is being transmitted, by accessing the SFD. My problem is that I'm not able to do it.
NRF got a function called...
Hi,
I'm currently trying to build a quick frequency spectrum scanning tool on an nRF52840 dongle. I want to sample RSSI on a list of channels as quickly as possible in a...
hello,
we're working with the nRF52833 and are experiencing some issue with the I2C interface during communication involving clock stretching. We're wondering if the errata...
Hello guys,
I am dealing with a problem, i have two tasks with two different spi instances, alone they work fine, but when i want to run both tasks they crash!!
Hi!
I met some issue ).
I use nrf mesh app on my phone and change it for my goals. I would like to get messages from nodes to phone via mesh. I read some posts that it...
Hi,
While developing an app which will connection to an IOS device via BLE - I've noticed an event called BLE_GAP_EVT_PHY_UPDATE_REQUEST.
I understand that this event...
Hi,
I'm using NRF52840 in order to connect to a mobile device, with PIN code.
Connection to Android is ok. The issue is with IOS.
IOS can't send the PIN code to my...
Hello, We're trying to optimize the data transfer rate from our nRF52832 based peripheral device to the mobile phone. Tested with two different BLE >= 5 Android phones we...
Hello, I ve made a custom nrf52832, but ive face a lot of problemes : when logs is on the BLE is off(its not advertising) , I m not able to see it on my app. when my module...
Hello,
I am using MacBook and would like to import Keil Projects into Segger Embedded Studio by following this guide , but finally I got an error is that
I have found...
I have some questions about nRF9160.
1. What is improved comparing to revision1? Only power consumption?
2. Is GPS sensitivity improved? In revision1, it is poor.
3...
