Hi,
I have a nRF52 DK board and I am trying to build a BLE peripheral with both connectable advertisement (custom with my own name and service) and unconnectable advertisement...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
I have a PCB with an nRf51822 @1.8V, using the SDK 10 (no chance to change it).
The PCB itself with everything but the nRF (we did not iron it on purpose to measure consumption...
I have downloaded the motion_driver_6.12 for Nordic Thingy 52 as given in the readme.txt file. And I am using Segger Embedded Studio to build and debug the code. But the IDE...
Hi,
I'm working on a project originally based on the light switch example of SDK 1.0.0 and then upgraded to Mesh_SDK 2.0.1 and nRF5_SDK_15.0.0
I use the code shown in...
Hi,
I am using nrf52840 and SDK-16.0. Our product is already in the market.
we added some extra features now. after adding this we are not getting application timer call...
Using VS Code, I've tried to build the "BLE UART service" (= peripheral_uart) for the nrf52840dk_nrf52840 board. According to the documentation, this board is supposed to...
Hi. I had a working MCUboot configuration that I used in order to update both the app core and the net core as follows:
- Upload the app core image using mcumgr - Upload...
I am working on a project that uses nRF5340.
We are now looking into designing software update mechanism. As a part of this, on the app core I am planning to move slot1_partition...
Hello,
when creating a multi-image build is it possible to select the optimization level for each image individually?
Below is an example of the issue I am facing currently...
Hello,
I want to add multi-image dfu over BLE to my NRF53. A simultaneous update seems to be the only option for this. Unfortunately, it seems we lose the ability to revert...
I have had great success developing a project based on the peripheral_uart sample. Now I am trying to add DFU over UART to that project. Specifically, I would like to add...
I have been experimenting with build configuration for the peripheral_uart sample project so I can add DFU. I have had a great deal of difficulty doing this because of unexpected...
Setup:
nrf connect sdk version v2.1.2
board: nrf52840DK
Trying to send a beacons for half a second whenever I get some specific data on uart, and also send data over...
nrf52840 17.1.0 s140 SDK :- examples/dfu/secure_bootloader/pca10056_s140_ble_debug
We are using nrf52840 17.1.0 s140 DK secure bootloader with BLE debug. We initialized...
I have an array of LEDs on my custom board. One of the LEDs is set on a UART0 RTS pin, which is GPIO(0,5), and we are using ground as common. To avoid any conflicts, I disabled...
I am using an IMU sensor in sensor hub mode (LSM6DSV16X, LIS2MDL) with the FIFO interrupt interval set at 30 Hz. The data is sent over BLE. It works perfectly when using RTT...
Hi Fellow NCS-ers, I understand that the configuration setting CONFIG_BT_EXT_ADV, CONFIG_BT_CTLR_SCAN_REQ_NOTIFY, and bt_le_ext_adv_create() with the appropriate callback...
I use custom board for nrf52840 but i have some problem with the BLE. BLE is advertised but when i want to connect it, it keeps connecting. this is my code. I use mbed before...