I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hello everyone,
as indicated by this question https://devzone.nordicsemi.com/f/nordic-q-a/35692/adding-nrf52-dk-to-github-mesh-demo-for-thingys/138327#138327 I am trying...
I am using the nRF52840, which has BLE support but does not have a touch sensor. Can you recommend a module that includes both a touch sensor and Bluetooth?
I'm now trying to test dongle on nrf52840dongle board：
1. west build -b nrf52840dongle_nrf52840 -- -DCONF_FILE=prj_4llpmconn.conf
2. open nRF Connect for Desktop's Programmer...
hi
board : nrf52840dk
sdk : nrf connect sdk v2.6.1
example: matter light bulb
problem:
I want to add another set of PWM to the sample code. How should I configure...
The docu page for the nRF9151
https://docs.nordicsemi.com/bundle/ps_nrf9151/page/ip/radio_lte/doc/frontpage.html
contains a link to
docs.nordicsemi.com/.../intro_nrf9160...
I have customed my own 52820 dongle board.
I wanted to run ncs2.7.0/zephyr/samples/subsys/usb/cdc_acm demo on my board to test whether it worked. So, I builit the cdc_acm...
Hi
I'm trying to make the UART-HCI example run on my nRF5340-DK board.
Environment: - nRF5340-DK Version 2.0.0 (2022.13) - nRFConnect 2.7.0
I've built the example with...
Hi All.
A few years ago, Nordic documentation for developers included many "examples" to practice with and learn about this technology. For instance, ... >examples>ble peripheral...
Hello,
I am in the process of adding LPN nodes to my network, Unfortunately I am getting a lot of "Ignoring old SeqAuth" Warnings and looking at the LPN friendship call...
Hi
i bound rtc in nrf52833 and set/get the time.
but the time is not incrementing ,iam reading the same time which i set.
i added the config below,
but no change in...
Hello,
I am trying to configure P0.9 as output and toggle this pin.
It is no possible but if I change the number of the pin then I can see the modification of the output...
I ran this exercise a month or two ago and it worked to do OTA updates. I then tried recently again and it is giving me "Device not supported" in the Nordic Device manager...
How can I get the lis2dh12 accelerometer speed at 1.344 kHz as mentioned in the datasheet from thingy52?
I have configured the registers as per datasheet of the accelerator...
I tried running the official ranging example with nrf5340dk.
Bluetooth: nRF Distance Measurement with Bluetooth LE discovery
Usage
This example can obtain distance test...
Hello,
I am working on the Raytac MDBT50Q-RX dongle which has the nrf52840 chip embedded. I am having issues programming it using the debug pins on the module, using the...
hi
board : nrf52840dk
sdk : nrf connect sdk v2.6.1
example: matter light bulb
problem:
I want to add another set of PWM to the sample code. How should I configure...
