Hi,
I'm using an nrfx_timer event with k_poll_signal_raise to trigger a thread to perform an operation.
I've noticed around 900ms delay between when the signal is raised...
I used the Bluetooth mesh distributor example from ncs2.9.1, and the Bluetooth mesh dfu can proceed normally. However, when I tried to pause and resume the dfu process, I...
I have a LIS2DW12 accelerometer connected to nrf52840 SPIM3, and I am seeing an intermittent failure. In some instances while collecting accel data during a data ready interrupt...
Hello,
I am looking to create my own custom NRF5340 AUDIO DK board. Could you point me to any NRF5340 modules that would be best to use with a pre-built antenna, available...
Hi,
I am currently working with the channel_sounding/connected_cs sample for nrf54l15 and I keep getting the error: Not enough memory to store step data (530 > 512). I tried...
hello Nordic
i am working with nrf52840 running ncs v2.8.0
this device connects with a central, via BLE, the central running on linux.
i am working with smp (simple...
I'm getting the following warning on my terminal during build:
-- Including generated dts.cmake file: D:/Workspaces/azure_iot_hub_9/build_pmi/mcuboot/zephyr/dts.cmake CMake...
We are experiencing some ESB link failures on the receiver end of our system: nrf54L15. After minutes to hours of use the receiver will stop getting data (we know the transmitter...
Hi everyone,
I'm developing a matter generic switch and I’ve run into a puzzling behavior when commissioning an nRF52840 DK with Apple Home via an Apple TV Thread border...
I’m using nrfjprog version 10.12.1 and JLinkARM.dll version 6.88 . I encountered an intermittent nrfjprog error when programming firmware to the nRF52833 .
In most cases...
Has anyone experienced the following error when Flashing (and debugging) from within VS Code. I have no idea what has happened, but it has hit several projects.
Even though...
Hello,
I am looking to use multiple PPK2 to measure current across 2+ voltage rails at the same time. Is there a way to connect 2+ PPK2 and synchronize the data from the...
Hello,
After a lot of efforts I managed to autoprovision and autoconfigure my nrf52840 board (provisioning and configuring inside the software and not through external app...
Hello, I am trying to develop a bluetooth mesh network with two provisioners, one being an external provisioner (mobile phone) and another being node in the network (nrf5340...
Hello,
I am using SDK v2.9.1 for a Bl653 (NRF52833) and was trying to use the Nordic Academy Example for how to setup the SPI bus. The Nordic Academy example states we must...
Hi,
I believe the default application on Thingy91x uses LTE-m to connect, which is working fine. How do we make it use only nB-IoT?
For Thingy91, there is a guide
Getting...
-> How to transfer data from one thingy52 device to another thingy52 device. If i have 2 thingy52 devices, I'll send data to 1st tingy52 then 1st thingy52 device will send...
Hello,
I am modifying an existing custom board with a sensor that requires exactly 1.9V VDD. Previously I was configuring REGOUT0 = UICR_REGOUT0_VOUT_2V1 but I was surprised...
Hello,
I am trying to play the AT45 DataFlash driver by directly copying the sample code from nRF connect SDK v2.9.1 (C:\ncs\v2.9.1\zephyr\samples\drivers\spi_flash_at45...
Hello, I have an application developed with the nRF9161 DK board, which essentially consists of a GPS tracker that acquires a position every x time and sends that same position...
