Hi,
I am using an nRF52840 as a Zigbee NCP. I have built the firmware myself using nRF Connect, and I am also running MCUBoot. Sometimes after some usage, the chip starts...
Hello everyone,
I am testing out I2C on the nRF54L15 for a custom PCB project.
I first tested a simple mpu6050 sensor on &i2c21 on pins P1.11 for SCL and P1.12 for SDA...
I have a bit of an unusual use case where the nPM1300 is quite ideal but need to use an external charger for the battery instead of the internal charger. The nPM1300 fuel...
Hello,
We are currently developing with the nRF9151 and would like to request more information regarding GNSS SNR testing.
We have reviewed the documented GNSS functionality...
Hello,
Is the nrf54 family's I2C peripheral compatible with I3C? I need to communicate with several I3C sensors on the same bus.
If yes, is the software support only...
I'm using the nRF Connect SDK on nrf5340dk and encountering issues when trying to use the non-blocking (asynchronous) I2C API.
i am particularly getting this error - ENOSYS...
Hello everyone
I'm currently trying to make dynamic endpoints on my matter device. I changed the .zap file to accomodate all the possible endpoints (16) with clusters...
This test program is modified from examples\pin_change_int\main.c, I add the instructions to put the cpu to sleep. And I add nrf_gpio_input_disconnect() for all the pins except...
Hello, I am using pstorage function and I would like to know oppionions of your's what would be the best practise to wait until processor erases the flash memory and would...
Is enable required before configuration? Does toggling NRF_ADC->ENABLE reset the configuration (like it does for the radio?) Is the power to the ADC automatic, so that even...
im using sdk10, I initialiszed ble_stack_init and advertising_init but when starting advertising, it works with BLE_ADV_MODE_FAST but not with BLE_ADV_MODE_SLOW .
why it...
Hallo comunnity
I have a sensor which is working is sending data via BLE and it has a 128 UUID bit service [0x 000000-000000-1000-8000-0080-5F9B34FB]
In order to do...
Hi,
What is available MTU of CoAP and UDP over 6lowpan with IoT SDK ?
In my application, I need to transfer dozens of kb data to ble node over 6lowpan with iot SDK. Do...
Hi, I bonded is ok .But I want to store some data on nrf51822 flash memory using pstorage. What should I do?
Register new or change it :
param.block_size = ALL_CONTEXT_SIZE;...
I have an SPI peripheral that has an odd protocol and in trying to sort out why it was acting up I finally caught a logic trace showing about a 13us break in the SPI data...
Hello,
I am using HID mouse/keyboard examples from SDK to learn creating custom HID device.
Besides using four buttons on EVK to simulate motion action. I would love...
Hi All,
I'm currently setting up three nRF52840 DK nodes, two nodes are routers and one is an end-device. My plan is to introduce more node in the network later on. The...
Hi,
We created a faster & simpler alternative to gazell for the nRF24LE1 (our IoT sensor) that supports 100s of transmitters (PTXes), is individually addressable, has session...
Hi
I'm using the NRF51422 with hardware UART.
Brief outline of the configuration:
115200 Baud, 8-N-1, no HW flowcontrol
SoftDevice S130 V2.0.1
lib: app uart fifo
...
Hi all,
I am using the softdevice S130 v2.0.1, plus one application derived by the ble_app_uart and the single bank bootloader (SDK11) on a custom board with the nRF51822...
