I'm using the nRF Connect SDK on nrf5340dk and encountering issues when trying to use the non-blocking (asynchronous) I2C API.
i am particularly getting this error - ENOSYS...
Hello everyone
I'm currently trying to make dynamic endpoints on my matter device. I changed the .zap file to accomodate all the possible endpoints (16) with clusters...
Hi community,
I have a similar custom board as Thingy53, which has the nrf21540 module on board.
my purpose is to turn on the nrf21540 and do the reconnection, when...
Hi!
With the release of NCS 3.0.1, the required SEGGER JLink version to v8.18. pynrfjrprog is bundled with SEGGER JLink v7.94. From your website, it seems nrfjprog, being...
Hello,
Over the past three days (up until today), we've observed inaccurate behavior in the Message Routing Service. Specifically, we shut down our destination service during...
Hi,
I use the nRF54L15-DK flash fimware (.hex) with "nRF Connect for Desktop - Programmer" success.
And I view the schematic, discovered the DK board have flash memory...
I have a NRF9160 design with a TPS63031 regulator providing 3.3v. When my battery gets weak I am seeing spontaneous reboots, likely due to input voltage droop.
I'm experimenting...
Hello.
I'm newbie in nrf51 world so maybe my questions will be a bit stupid.
I bought few nrf51822 modules on Aliexpress. Photo: www.dropbox.com/.../77_1.jpg
I bought...
Hi,
When trying to install nrf5x Command line tools 8.4.0 (under windows xp), the setup program ends with an error (see nrf5x-cmdlinetools.log ).
It seems to do with...
I want to be able to read my i2c and program logic flow within the BLE application but when I try to set breakpoints it causes the cpu to do a hard reset. How can I capture...
I have an nRF51822-DK board and so far I could not properly grab from the examples a simple thing: is there any specific initialization needed when coding?
For example...
Hi All,
I'm currently developing a network where I would like to use nRF52 SoC. The nodes in the network must be able to extend to over 100 and must be able to multi-hop...
Hello,
I've taken the example from the SDK 12.0.0 for RAM retention. I've added additional NRF_LOG statements to check if the RAM retention is happening. I do not have...
Hi all,
In the Data sheet ,i saw it is a short cut register . It is available for all the peripherals with offset 0x200.
Can you share more information about it, like...
Hi
We are developing a board with nrf51822 and we are looking for the PCB design layout guideline.
We actually went throught the PCB design tutorial on the nordic developer...
I'm attempting to build the ANT+ examples within SDK 11 and am hitting an issue in compile:
C:/Compilers/nRF5_SDK_11.0.0_89a8197/components/ant/ant_stack_config/ant_stack_config...
I'm using Arch Linux, with kernel 4.9.6 on a 64-bit laptop. Using a window manager with no desktop environment.
I'm trying to install Segger Embedded Studio 310i , which...
Hi,
I am working with nrf52DK and Sim800l, I want to send some data using GPRS commands like AT etc.
I am having a market build module for Sim www.circuitstoday.com/....
Hi,
I am using the example code supplied by the blog for reading humidity from the HTU21D sensor using TWI . My humidity and temperature readings are constant and never...
The code generated from the BDS plugin (v.1.2.4, found here: question including link to v1.2.4 ) is failing because of missing references to boolean_t and bds_boolean_encode...
