Hi,
we have ESB PTX and PRX couple from nRF54H20 nRF54H20DK (rev. 0.9.1), SDK: v2.9.0-nRF54H20-rc2 and the same Toolchain, IDE: VSCode + nRF Connect plugin build for CPURAD...
We are currently developing a project using the nRF52832 as the microcontroller, Segger Embedded Studio version 5.42a as the IDE, and the nRF5 SDK 17.0.2. We began by creating...
Hi.
After migration from SDK2.7.0 to SDK2.9.0 I have issues with power mangement. CONFIG_PM_DEVICE_RUNTIME=y, which I used, causes that twi driver doesn't start. I try to...
Hi Community
Greetings, I bought nrf9151 DK module looking at the features, power consumption & size but the fact that NB IOT has a communication rate of 15mins once in...
Hello everyone.
I am developing a custom board using the nRF9160. I tried using the RAM power-down library based on the Power optimization recommendations page of the nRF...
Since the nRF9160 reserved pins are never used, Is there any issue leaving them out of the footprint?
I would place copper keepouts under the reserved pin areas to ensure...
gaps.zip
Hi,
I have a code that continuously toggles a pin(I use nrf_drv of gpiote+ppi+timer2 for this purpose and interrupt time = 30usec). I have basically taken the...
I know the things like the TWI allow you to send additional data when you instantiate a transacation. Is there any way to do a similar thing with UART?
I'd like to pass...
Hi
I'm using the PeerManager/FDS/FStorage in my project since a few months. We have this software running on real hardware and on simulated environments. While researching...
Hi NORIC's Engineers:
I am a handware engineer who is from Jetway company in China.
I am sorry for my english skill to descripe my questions about NFC antenna of nRF52832...
Hi!
I'm am working on a project where there I need to connect two nrf51 modules and a phone.
Say: Module A, module B and phone P.
The setup i a bit tricky to explain...
I want to use three ADC-inputs on my nRF51832 Engineering Sample B. I read that it is possible to define several ADC-Channels and if a ADC Sample is triggered all Channels...
Hello,
i have a characteristic kept in user space with VLOC_USER. It has read/write with response props and has auth permissions set, both for read and write.
In the...
'morning, I'd like to know how to wire a BMA250 to a nrf52832 please ?
Screenshots : (BMA250) http://prntscr.com/bil9ng
(nrf52832) http://prntscr.com/bil9uu
Thank...
Hi
I've discovered last week some unexpected resets by the watchdog. I guess I've the explanation and the workaround for the behavior, but it would be great to have this...
Hi I am working on activity detection using ADXL362 and nrf52. When I am moving the accelerometer ideally I should get activity interrupt in status register and when ADXL362...
Hi,everyone,
In my project ,I want to save some data when disconnect evt happens; here is my code:
the problem is ths program always stuck in power_manage() function; what...
I'm basing my schematic and antenna design using the PCA10028 as a reference.
I'm not including the J1 RF-connector into my design. Do I still need to include both C6 and...
I only hope that their devices can link their mobile phones, other mobile phone links may not link, but I didn't want to enter a password, directed broadcast method can, about...
I am using the nRF52832 as a MCU in the wearable device,now i want to use the spi master mode to collect data and store data ,and when it is necessary,I want through the bluetooth...
Hi
I have been working with nrf8002 chip. I simply want to program the hardware in a way such that it gives out a signal that can be detected by the emulator.
