Hi,
we have ESB PTX and PRX couple from nRF54H20 nRF54H20DK (rev. 0.9.1), SDK: v2.9.0-nRF54H20-rc2 and the same Toolchain, IDE: VSCode + nRF Connect plugin build for CPURAD...
We are currently developing a project using the nRF52832 as the microcontroller, Segger Embedded Studio version 5.42a as the IDE, and the nRF5 SDK 17.0.2. We began by creating...
Hi.
After migration from SDK2.7.0 to SDK2.9.0 I have issues with power mangement. CONFIG_PM_DEVICE_RUNTIME=y, which I used, causes that twi driver doesn't start. I try to...
Hi Community
Greetings, I bought nrf9151 DK module looking at the features, power consumption & size but the fact that NB IOT has a communication rate of 15mins once in...
Hello everyone.
I am developing a custom board using the nRF9160. I tried using the RAM power-down library based on the Power optimization recommendations page of the nRF...
Since the nRF9160 reserved pins are never used, Is there any issue leaving them out of the footprint?
I would place copper keepouts under the reserved pin areas to ensure...
Is it possible to get to port of an UDP socket (ephemeral, offloaded to modem) with NCS 2.9.0 and mfw 2.0.2?
I tried "getsockname" and get "errno 95 (Operation not supported...
I am trying to trigger some functions based on some pre-determined timings. I tried to do that using nrf_delay_us and also using timer0 interrupts, but both are giving me...
Hi,
I'm using nRF Master Control Panel to test a Phone Alert Profile (PASP) I've implemented. For this, in the app I configured a GATT server that exposes the Phone Alert...
Hi,
I am using nRF5_SDK_11.0.0 to learn how to use BLE stack to communicate.
For the BLE HRS app, I want to achieve sth. like this:
Central node can configure the sending...
Hi,
I'm not sure if this forum support that board but if YES, can You explain how to upload some program on that board. I think that process is little bit different that...
For some of the examples i see different versions
For example the ble_app_hts example
It has a _hci, _spi and a _uart version
In the documentation i don't find any info...
hello everyone!
I have just contact nrf51822, the agreement with the application framework is not very familiar with, you can share a quick start of the information, the...
Hi everyone,
Where I can read transmission type and device number of connected ANT+ device (HRM)? I want save those values and bound later only with currently connected...
I tried to set a custom key in this way:
... ANT INIT
uint8_t network_number = 2;
uint8_t p_network_key[8] = {0xa1, 0x15, 0xb3, 0x66, 0x60, 0xef, 0x19, 0xa1};
err_code...
Hi there.
I'm woking with sensor in board nRF51822.
Do we have any tool to test oscilloscope i2c?
I want to check the signal is same as what I sent or not.
Thanks...
Since nRF51 is multi-protocol, why don't Nordic provide support for Zigbee? This way, customers can simply buy one single chip and have several standards supported. Are there...
I received a NRF_ERROR_INTERNAL error from a pstorage_store() function. As far as I can tell this error should not result from this function. It occurs fairly randomly. This...
In the examples delivered by Nordic, there is ble_app_hrs in ble_peripheral and ble_app_hrs_c in ble_central. But I cannot find a ble_app_hts_c in ble_central for the ble_perifpheral...
I am using Master Control Panel to check some off the shelf BLE product. I noticed that some of them don't provide characteristic value when I press "discover services". ...