Hello Team,
I am currently working with the nRF52832 and using the nRF Connect SDK ( NCS) with toolchain version 2.9.1. I would like to interface the nRF21540 RF Front-...
I don't have found CONFIG_OPENTHREAD_FTD feature in the bulb project prj.conf or prj_release.conf file, but I have found that it is enabled in the final .config file within...
I have installed nRf Connect for Desctop v5.1.0 on my windows 11 system.
I tried to update the Quick Start and install the Power Profiler.
Both gave me a similar error...
Hey All! I've been following the nRF Connect SDK Intermediate course from DevAcademy. In exercise 2 of lesson 9, bootloaders, you get to learn how to use KMU (Hardware Key...
Hi,
Testing Hardware: nrf52832 Module in a Custom board OR nrf52DK possbile -> We would like to change the order of the BLE service as shown in this thread: https://devzone...
Hello, I am trying to use the nrfx driver example to run an RGB led connected externally to the nrf5340 board. I dont see the led/pwm cycle running successfully. Can anyone...
hello, I started working on BLE mesh using nrf52832 QFAAE1. from hardware side i have custom self design nrf52832 QFAAE1 lot's of board, and every board working, i verify...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
I have opened the nordicID sample project "InventorySample" for Windows CE in VS2008 it successfully builds the project but when i deploy it on mobile simulator Pocket PC...
Hi,
I'm using S132 v2.0.0 and nrf52832. I've got a problem when I'm trying to call any softdevice function from radio notification event handler.
#define RADIO_NOTIFICATION_IRQ_PRIORITY...
I am using nRF52832 DK and we designed a custom board using nRF52832. I am using a windows 10 lap. It used to program successfully from windows 10 lap and boards will advertise...
Hello,
I use nrf51 based device as peripheral with SD110.
I use connectable advertising ( BLE_GAP_ADV_TYPE_ADV_IND, BLE_GAP_ADV_FP_ANY ) and turned on BLE_GAP_EVT_SCAN_REQ_REPORT...
Hello,
what address in flash is it safe to store my application settings (some calibraton data) which should be preserved during application updates. I use S110 v8, dfu_dual_bank_ble_s110_pa10028...
Hi all, i'm trying to understand how to program my nrf51 DK in order to perform a temperature measurement with the onboard sensor, convert the battery voltage with the ADC...
I use dfu_dual_bank_ble_s110 bootloader from SDK10. I want the bootloader to check whether if incoming firmware is compatible with the device it is uploaded to (i.e. device...
Hi
I want to connect to only a single master device by s110. I used the example parameter setting from "ble_app_hids_keyboard" for gap_params_init, advertising_init and...
I have modified the Android Blinky App to connect two peripherals (nRF52 DK)
Scanning and Connecting to two peripherals works.. but when i want to start sending notifications...
Hi, all.
I want read mouse cursor coordinates from connected target(PC or iPhone and so on) through HID.
And then, i want to align the mouse cursor in the target center...
Hi.
I tried "Go to definition Of 'sd_softdevice_enable",and
"Go to Reference To 'sd_softdevice_enable" at ble_app_hrs_c at ble_central,example .
But sd_softdevice_enable...
Dear all.
Now we migration from SDK 10 to SDK 11. but, there is not SDK11 packs. As you know, no pack is very uncomfortable for package managing on keil. please answer...
Hi,
I am using nrf52-DK (First Version in the moment) and need to test UART interface.
I use the example from the blue-nus example from the SDK which is working fine....
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
