I am trying to get a WiFi project working using the nRF52840DK and nRF7002EK . I use a 3.3V power source that is supplying power to both nRF's in parallel. For the nRF7002EK...
Hi,
I'm developing firmware for the nRF52840 DK using nRF Connect SDK v2.9.2 , and I’m running into a problem that didn’t occur in v2.8.0 .
My project uses Zephyr and...
I am receiving an error when connecting to a custom board by running nrfjprog --reset, any similarly with any other commands that require connection.
I am connecting through...
We have previously used nRF52840 and for the latest iteration of our board design we are updating to use nRF54L15.
We are aware that for nRF52840 we could map any pin to...
Hi,
I faced with an initialization issue of combination two features: MCUMGR and UART_ASYNC_API. I get a crash right after the FW starts. It looks like the SW configuration...
I checked the nrf52832 manual and found that both XC1 and CX2 are analog input pins for the 32Mhz clock pin configuration. The reference design for both uses 32Mhz crystals...
Hello, I need to configure and compile a sample to send an audio stream (mp3) to the I2S interface.
I tried to put together some configuration from other samples but no...
Hello Everyone,
I am designing the prototype using NRF51822 and i have choosen the DC DC power mode but the real problem is most of the time my radio will be sleeping so...
I have nRF52 Development Kit (PCA10040). I'm using Keil uVision.
I want to measure RSSI of some beacons and if the signal is strong then send MAC of this beacon over UART...
Hello Everyone
I'm trying to debug ble_app_beacon project, having the following error when trying to launch the debug session:
Error in final launch sequence Error executing...
Dear Sir:
I have a (BLE + 2.4GHz)Mouse project, But now I had some problmes. Please help deal,
Thank you so much Sir.
a). My program modification base on "nrfready_desktop_2_v3...
Hello all,
Just to note any versions that need saying, I am using
SD 110, V8
The 10.0 SDK, freshly unzipped
The dual bank BLE bootloader, unmodified
Arm...
I was looking at this PA/LNA example: here . I noticed something I'm not sure about, so I was hoping someone could shed some light on this.
In the diagram shown in the...
I've been working on a project, which requires data transmitted through ble to cell phone app. The user could acquire the data from the sensor when he sends a specific string...
Hi
We use the NRF51 in a mesh sensor network. We noticed in a trailer suited for cold chain transport (double metal walls with thermal isolation between) that the radio...
Hi,
I have problem with ble_nus_c.c in SDK v11...
Normal operation is:
Connecting to target 57E19A190FDF
Connected to target
[DB]: Starting discovery of service...
When I used the demo of ble_app_hrs_rscs_relay,I cannot write the bonding information to the flash.
I connect to the board by my phone.I cannot find the information about...
what I am basically trying to do is only allow a single bond and any new bonds disallowed until the user selects and option to allow a new bond and then and only then delete...
If I have 10 slaves and one master in a bluetooth low energy network, and the connection interval for all 10 slaves are set to 7.5ms, how would the master manage this?
...
I intend to use RC oscillator instead of external crystal oscillator .
I modified code :
from
SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, NULL);
to
SOFTDEVICE_HANDLER_INIT...
Hi,
I want to identify different kinds of center in a device product. So I have 2 questiones:
1) Can a center (running S120) set its own name?
2) Can a device (running...
HI,ALL
There are such statement in the CORE SPEC 4.2
"
If the Link Layer connection supervision timer reaches 6 * connInterval before
the connection is established...