Hi,
I started the LBS example on the nRF52DK_52832 kit and connected the PPK2 kit to the P22 pins for measuring power consumption. I am not sure if I did something wrong...
Hello forum ,
As i m working in nordic nrf52840 where i have taken adc value of photodiode ,then i have created service and characteristics i will share the image for that...
Hi,
Does Central or Peripheral UART enable ACK/NACK in the code for BLE communication? How does Peripheral recognize if Central has received all the data ? Is there any...
Hi
I had a device that did not start up - because it was waiting for the 32KHz clock to be stable.
So I tried to change the setting below from 15pF to 5pF and it started...
Dear forum, I am testing out the radio on the nrf5340 using two evaluation board connected to a SES setup, but the receiving board only gets garbage and the checksum is never...
-> How to transfer data from one thingy52 device to another thingy52 device. If i have 2 thingy52 devices, I'll send data to 1st tingy52 then 1st thingy52 device will send...
I want to measure the RSSI strength of my Bluetooth module, in various distances and situations.
I read in the description of the app nRF Master Control Panel that:
...
I'm trying to change the mac address of my nRF51822 chip using something like:
ble_gap_addr_t m_address_1;
m_address_1.addr_type = BLE_GAP_ADDR_TYPE_RANDOM_PRIVATE_NON_RESOLVABLE;...
Hi,
I use GCC for compilation and nrfjprog for flashing. A few weeks ago I needed to switch on compiler optimization (Level 1) because my code grew a little too big. Now...
Hi,
I would like to have several nRF51 development cards connected to my computer at the same time using the USB debug port. The serial port and the RTT port work when several...
Hi,
We are trying to develop application with OTA DFU on nRF51. And we need to build bootloader ourselves. We use gcc for development. We found the bootloader example for...
I tried to run beacon example (from SDK 9.0). Even after uploading hex file I was not able to "see" becon. I'm using st-link v2 and openocd. Let me tell a bit more about what...
Hi,
I'm making device with nrf51822 chip and 400mA battery.
It connects to smart phone.
It has to calculate heart rate and some other things, so it's doing it on device...
Hi All,
I just bought the Nordic Semi nRF51822 DK (without the starter kit). I tested the Heat rate monitor app and it worked fine. It could send some random values to...
Dear all,
I tried the example program ble_app_uart given in the examples section of the Nordic folder in Keil installation. I created the hex code and programmed my chip...
I was just at the Nordic nRF52 Global Tour in Atlanta and I received the nRF52 Development Kit (PCA10040). One of the Nordic engineers mentioned that the nRF52832 is at rev...
Hi all,
I am using the BLE nRF8001 and EFM32 (ARM Cortex M3). I used the following SDK for connecting the modules using ACI (SPI). github.com/.../ble-sdk-efm32
Now I...
brownout reset = 1.7V
Operating conditions VDD(Supply voltage,internal LDO setup) = 1.8V
(by 1822 Product Specification)
In between 1.7V of 1.8V, or it would have been...
Greetings, I've been using the ARM GCC tools for about 2 months with success for programming the NRF51 DK board. Now I would like to try out the example found in:
examples...
I run step by step the example of adding DFU to ble_hrs, everithing runs fine.
I try to change in the same way another example, ble_app_proximity.
The problem is that...
