Hello support team, i have an issue regarding the i2c configuration on an nrf52832.
The Setup is:
EvalBoard nrf52dk_52832
BME280 Sensor attached via I2C
NCS 2.6...
hardware:nrf5340+npm1300
software:ncs 2.5.1
hi professor,
If I just connect VBUS, The npm1300 will reset when I read bulk register. If I connect vbat and vbus, read...
Hi.
I am trying to disable the RESET pin (P0.21) on the nRF52810 microcontroller (custom board) and set it up as a normal I/O pin.
I'm using the SDK v2.6.0.
I don't...
Hi,
I am working on a project which has external flash (FM25V01A ) connected to nrf52832 board over SPI. And when building the project, I am getting the following error...
On the nRF51, LO leakage was measured when in receive mode. For 2402~2480mhz, LO leakage was measured at approximately 2745~2836mhz. The nRF52 does not measure LO leakage...
I've got a project based on NCS v2.6.0 using a nRF52840 as contained in a Fanstel BT840F module.
With help from you all (thank you!), the software works. Bluetooth and PWM...
I'm organizing my code with nRF SDK v17.0.0,using the board nRF52832 that designed by myself.
In order to support multi-central,the peer_manager module is used.So that I...
Hi! I'm developing using nrf52840DK and have an issue with DFU. When I'm uploading new app image and choose test and confirm, image is uploaded but after resetting DK, MCUBoot...
Our hardware designed with nRF52840 and npm1300 works perfectly.
We are working on an architecture where a single central communicates with four peripherals...
Hi,
I'm trying to use the periodic sync sample app using 2 nrf52833DK (one for advertising and one for receiving sync) and been getting this assert message every time a...
We use nRF52832 to develop our sensor.
Then SDK version we used is 14.2.0, and the softdevice is S332(ANT_s332_nrf52_2.0.1)
Now we develop the FW hex file with softdevice...
Hi,
When using the NFC record example, bringing an Android phone close to the NFC tag automatically pops up and displays the text content, but an iOS phone does not automatically...
Hi I am currently using NORA-B106 based on nrf5340 to work on ble multilink things. For right now I can do multiple connections by adding several scanning filters. But I cannot...
Hi All,
I'm trying to fully disable all location services with the asset tracker in v2.6.1 while using lwm2m (so I have the lwm2m overlay enabled in the build settings)...
Hi,
I'm stuck in the Cellular IoT Fundamentals course on lesson 2, exercise 2. When adding build configuration I get the following error:
[31/167] Building C object secure_fw...
I would like to integrate the PPK into an automated test system. Are Python drivers available to query the PPK directly for current readings, power control, etc.
I'm trying to test minimum timing and performance using peripheral and central ISO under Zephyr.
I'm trying to play with the interval and latency values under the central...
When I try to debug a programm (build with "optimize for debugging" and debugging started by pressing "Debug" in VSCode) I get to the debug-view and can also go one or a few...
We are working on a custom board (gateway BIS) with the nrf5340. Currently our system is on the 2.5.2 SDK and we currently have FOTA working with an external QSPI flash and...
psa/client.h describes and defines PSA_MAX_IOVEC as follows: Just to be sure: This means that psa_call can only pass 4 input- and output vectors in a psa_call(), or? (E.g...