Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
software: ncs v1.8.0
hardware: my test nrf52833 board, with 9 antennas.
I do experiment like this:
aoa rx: in "nrf52833dk_nrf52833.overlay" file, I set " dfe-antenna...
Good day all.
Im finding my self working in a circle and not quite sure how to go about this. My USBD_HID device code with my Neopixel lib work well together. I now need...
[Environment]
nrf52833 chip, NCS 1.6.0
using uarte 1 with async API, baudrate 1Mbps, CONFIG_UART_1_NRF_HW_ASYNC=y and CONFIG_UART_1_NRF_HW_ASYNC_TIMER=2.
using ring...
Hi! We develop multilink central FW for nRF 52840 having NRF_SDH_BLE_CENTRAL_LINK_COUNT = 6. For enumerating connections and get info about concret connection, we use array...
Hi,
The customer needs to mass-produce more than 10KPCS nRF5340
Please give me the mass production scheme to be provided
1 . On the computer 1 drag 8 programmer software...
Hello, I have 2 nRF52840-dk developer boards. I'm having a strange and somewhat annoying behavior with the boards. If I haven't connected the boards for a few hours to the...
Hi everyone,
I am a beginner developing projects with nordic boards and currently am using the NRF9160DK. I just made an application through Ble MCU (nrf52840) and I want...
I am still learning how to develop on the nRF52 DK. Nevertheless there are many BLE devices in the market that change their own characteristic / attribute values after connection...
Isn't there a way to retask the JLinkARM on my Nordic PCA10028 dev kit for the nRF51 series to program the nRF51805 on the Fanstel BC805 board? Going manual with nrfjprog...
Hello,
I am a research assistant at the Norwegian University of Science and Technology. We have in the past been using the micro:bit v1 for our practical labs which purpose...
Hello Everyone,
I am working on NRF52840 development kit. I am trying to run I2c master. My main goal is to send some data to slave via I2C lines. I am using the example...
Hi everyone I have made an application running BLE and OpenThread based on nRF5 SDK for Thread and Zigbee v4.1.0 and I am facing some interference issues with Openthread network...
Hi,
We've been using nrfjprog with no particular issue for a while now. Usually to fully flash a chip (whether it's for a complete re-flash or for a new chip) we run those...
I am mid-way through development with the nRF52840 DK and Zephyr using the VSCode extension. I'm using v1.8.0 of the SDK.
I am looking for advice on setting my configuration...
Hello Community, I'm using the current sensor INA219 with NRF5340dk. Communication is through i²c protocol and using nrf SDK v1.7.0 . I'm trying to get the data output (Voltage...
