Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
Hi,
I am just staring my evaluation with nRF9160-DK. The video says I need to turn the dev board on, insert SIM card and wait for LED3 and LED4 to light before proceeding...
Hello,
My firmware is based on the ble_peripheral_HID_mouse (nrf52 DK, pca10040e_s112). I receive unexpected BLE_GATTC_EVT_HVX events of indication type from Client side...
Hello, I am using nrf52840 dongle for development purpose whether there is any provision to generate the code which is used by nrf connect for desktop from the app or by any...
Hello, everyone.
I'm dealing with an example of a sensor in SDK v14. I've checked it's working and now I'm going to put it in the code I made in SDK v17.
Code must be...
What happened to SDK 7.0.0
It is no longer available for download.
I assume some problem was discovered, so it should not be used any longer, at all?
Any help a...
Hello,
For clarification I use the nrf5_SDK_for_Mesh_v2.1.1. and the nrf52832.
I'm trying to scan for Ibeacons in which I need to get the UUID, major, minor, and the device...
Hello,
I have intention to use NRF52840 as HW peripheral just for communications over BLE. It means, it will be connected to the main MCU and provide interface for utilizing...
I am using nRF52840 Dev kit (PCA10056) , with nRF Mesh SDK 4.0 and nRF SDK 16.0 .
I have such FOUR kits . I have been able to modify vendor model for a sensor to transfer...
Hello everyone.
I'm a fresher of programming nRF52833. I'm doing an application for my final project in my university. What I need is get the RSSI in order to analyse the...
Hello -
I am evaluating nRF52840 to replace the Bluegiga BLED112 in an older product. I am surprised to get very low range from the nRF52850 USB dongle, barely 10-15 feet...
Hi, NordicTeam
Nrf52805 as slave and mobile phone as master to connect slave. NRF_SDH_BLE_GATT_MAX_MTU_SIZE = 247, MTU = 23, the master sends the Prepare Write Request to...
Hi,
I'm developping a new application where the device normally is in low power (waiting button with an interrupt)
while(!gIsButtonSwitched) { __WFE(); }
the consumption...
Hi everyone. I have an application using BLE and OpenThread dynamicaly. I am working with nRF52840 chip with nRF5 SDK for Thread and Zigbee v4.1.0 (Release Date: Week 18,...
Hello, I am using the Zigbee CLI Agent as coordinator, and when a router device or end device joins the network I want to configure attribute reporting.
I am able to configure...
We are running a trial in an open field, where we connect NRF52840 ( GW ) to an NRF 52833 (Node ).
Distance between the units is around 80 meter , we are using Coded Phy...
