Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
Hello everyone, I'm using the nrf9160-DK and I'm trying to read data from an external sensor over UART and I'm a bit lost. I would appreciate if someone could point me in...
I'm in the process off trying to learn the world of BLE. Currently, I'm using nRF Connect for Desktop (w/USB dongle) as the learning platform. Using 'Server Setup' I configure...
We use the chip product of nRF52810 to do a wireless module design. While in sleep mode, we found some spikes, which are 0.6mV in amplitude and 180ms in period. It is not...
Hi,
we use CC310 (in nRF52840) in a project (working directly with the CRYS API from SDK 15.2.0). When doing a test of ECDSA with secp256r1, following the one given within...
Hello,
I am trying to change the tx power for my nRF52-DK which is having nRF52832 chip. I trying the following code to change the tx power to -40 dB.
int8_t tx_power_level...
Is there any example about the dongle nrf52840 act as a central? Is that possible? In that case for a ble connection between dongle and board a service does to be create on...
Hello,
I need to long WRITE AND long READ from a central/client (android) to a peripheral server (nrf52). when I says long it means longer than the MTU.
LONG READ
I...
At the top of the Nordic home page, there's a link for "Bluetooth Software":
Following that takes us to https://www.nordicsemi.com/Software-and-Tools/Software/Bluetooth...
Hi!
In a Bluetooth mesh, we would like to get a feedback message from a group of nodes, via a reply message, after sending a message to the group.
The Bluetooth blog writes...
Hi. I am trying to get the peer address from of the peripheral my central has connected to within the BLE_GAP_EVT_CONNECTED event.
The following returns the address, however...
Hi folks,
I try to do create timer. Therefore i want to adding some files in blinky project. So here is some screen shot. Thats about debug error. First i used SDK 15...
Hi team,
I was asked by one of my customers, that if they can use nRF51822-QFAC (existing products design) as peripheral while connected by 2 central (Phone & Router)...
Hi I am a fleding embedded system engineer trying new ways to develop a process( Flashing) in my company,
My company's senior software has designed a control box which...
Hi,
I am facing problem while developing code for the application.
I am working on the "ble_app_uart" example code to develop my one of the application, But after making...
I'm using the code from Vidar supplied here . It works well, but shuts off after 3 minutes.
Based on the idle_state_handle brief, " If there is no pending log operation...
