There is the board mark on the chip like n51822CEAAD01350A0, where DO is Build code, 1350 is tracking code(YYMM), A0 is lot code.
My question is how can I get those codes...
I'm trying to debug a randomly occuring Hardfault. In trying to trace down the source I read the CPU registers use the Nordic hardfault_implementation.c which grabs the register...
Dear nordic employee
my purpose is send a data the length is from 150 to 273
when my server device send data by sd_ble_gatts_hvx（the send length is fixed 10 bytes） ...
Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi there, I have a custom board with nRF52840 and i am transferring fairly large amounts of data via uarte. I am also using my own driver. For some reason the attached device...
Hi,
I am Using NRF52840-DK Board. We are trying to transmit multiple data using NRFx_SPIM Example. for single reg read it is working fine.
please check below code is...
Hi,
I have certain doubts regarding simple message model .
1. Why simple_message_client_init or simple_message_server_init is never used? Don't we need this function to...
Hello,
I try to control led light of the thingy52 throw a MIT app inventor application.
I use the UUID : ef680300-9b35-4933-9b10-52ffa9740042
and thr characterixtic...
Page 362 of nRF52840 product specification version 1.0 March 18 shows A in 5 bits. The max entry is 0x0D (4 bits) and there has to be room for 8 entries in 32 bits. Hence...
hello, is there any way to generate DFU package without using command line. i am using segger embedded studio can directly generate dfu package in segger embedded studio please...
What is the wake time for module if i put module in system off mode in following cases .
case 1: Module will wake up by GPIO signalling
case 2: Module will wake up by...
Hello,
I need more details on DFU mode entering topic. I understand how to configure DFU to enter the bootloading mode on button press event but have dilemma about using...
I’m doing a project using NRF51822. We use P0.06 pin for PWM out while reading ADC from P0.01 P0.02 P0.03 & P0.04 .
As my experiment, when I’ve used P0.01 P0.02 P0.03 &...
Hello everyone, I was wondering if we could run IPSP over 2 BLE-supported nordic kits and ping one from another without using a BLE-Enabled router, like connecting them together...
Good morning everyone,
I am writing a custom protocol using the RADIO module and I am having a hard time understanding the address organization.....
My protocol supports...
Hi,
I want to interface an analog front-end Device through NRF52840-DK board Using SPI Interface . I want waveforms to be as Below:
which driver I suppose to use is...
Hi,
I try to Toggle ON/OFF the PWM using simple code below.
The PWM does not generate any output.
Please see code below;
/****************************************...
