Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
Hello,
I've been trying to learn to develop an app based on ZigBee, it's the first time i'm working with nRF hardware and the only things i've done so far was to run some...
Hi,
I am currently trying to embed the ATT_MTU throughput example on two nRF52840 dongles. The main issue I am facing is that after I compile and program the hex files onto...
Hi everyone,
I am working with the nrf52832 Dk boards,
So my question is I want to connect sensors to two nrf52832 boards and want to get their data on a single Android...
Hi.
We use nRF5_SDK_17.0.2_d674dde as central
And phone as peripheral.
Usually system works correctly for a long time.
But sometimes it enter in strange state.
Connections...
Hi
I would like to store data in memory and to be able to read them after. But I don't know how to proceed ! I use IDE segger. Is it possible to store data always in a...
Hi,
I use MQTT_Simple example with AGPS feature;
I add 3 functions, one for init GPS, one for start GPS, and the last for A_GPS request.
I call Init after "MQTT client...
I'm having some difficulties sorting out what support there is for the nRF52832 in ARM's Mbed. Specifically, whether Mbed v6+ uses the SoftDevice or not.
Some things that...
Hi I have recently started to use nrf5340dk for a 'pet' project. I have developed some code for both app and net.
Then I started to note have some trouble on the serial...
Hello world :-)
As there is no Issues section in sdk-nrf I will post my question here. After west update I cannot build my firmware anymore. I am using v2.6.0 Zephyr and...
Hi,
We developed a code using Fanstel nrf52832X BLE using serial UART command to control, receive data and send data.
The softdevice is s132_nrf52_6.1.1_softdevice.hex...
I2C burst write for nRF5340 at 100kHz is failing with a reply of -5. (Trying to use the BMI270 drivers sample, it will fail during reg_write of the configuration file)
Reading...
hi
I have nRF9160 dev kit, which I am using in a LAB with a private LTE SIM card, which has 99920 PLMN ID.
The network supports Band 3, and NB-IoT is configured as an...
Hello everyone,
1st of all, thank you for taking your time to have a look over my "problem".
I have a device that I am working on, that acts as aperipheral, it is...
