Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
I wants to use break point in project but when i set break point then 4 or 5 times working after that goes to NRF_BREAKPOINT_COND, I am using nRF52832. so guide me where is...
Hi,
I am trying to setup the serial UART DFU process for a custom board. I am able to build and program a combined firmware hex file which includes - Softdevice S140 ...
Hi guys
I have a project that needs to use multiple 1.8V sensors and transmit data to the mobile phone through Bluetooth. If NRF52832 also uses 1.8V power supply, it can...
Hi Everybody,
I have obtained a free personal Segger Embedded Studio license to use on a nRF52 evaluation board and started to write and debug code.
When I port my code...
Hi,
I use the latest connect sdk 1.4.0 and modem firmware 1.2.2. If I load the default aws_iot code it does not subscribe to the topics set in "topics_list" in the code...
I am using SES Nordic Edition 4.52 and I am building a Zephyr project configured with nRF Connect SDK. After the initial build completes, every time I build without cleaning...
I have a device using the nRF51822 chip on which I was successfully using the BLE sniffer V3.0.0 PCA10028 firmware. The latest V3.1.0 PCA10028 firmware does not work but I...
I am trying to download version 8.31.1 of the nRF device firmware pack for keil from this link
developer.nordicsemi.com/.../NordicSemiconductor.nRF_DeviceFamilyPack.8.32...
Hi.
I'm trying to integrate the MPU9250 with nRF52832 using i2c (TWI) on my nRF52-DK
I have found various libraries but none of them are working on my hardware. All of...
After several record updates one by one I get FDS_ERR_NO_SPACE_IN_QUEUES. However after each record update I wait for FDS_EVT_UPDATE event. I was sure that waiting for this...
I have %XRFTEST working on the 9160 in every band listed in the datasheet other than Band 14 and 17. Is there a reason these bands are not supported with the test mode?
...
I'm looking into integrating the SoftDevice controller (not full SoftDevice) from nrfxlib into NuttX RTOS. NuttX would already provide the host layer so I would only need...
Hi,
We are evaluating use of the NFC functions on our nRF52840 - based solution (currently we use BLE). I have been able to understand how NFC Tag payloads are setup within...
Hello,
Is calling --eraseall before calling --program the same as combining --program with --chiperase?
Does --recover erase all the areas that --eraseall and --chiperase...
Hi Dev team,
I am working around with the Thiny91 and wanted to have more information regarding the power consumption characteristics of the board.
I have a program running...
