hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Hello,
we are using the nRF52840-DK.
File: secure_bootloader_ble_s140_pca10056.emProject
File: ble_app_buttonless_dfu_pca10056_s140.emProject
In short, we are...
Hi,
I have a well working cli environment under linux where i can compile, program and debug a nFR52 demo board.
I have installed RSSI Viewer (1.05) and Bluetooth Low...
We want to deactivate Mesh DFU packets relaying from the App side to avoid messing with the bootloader firmware. Is there any flag we may use for that?
Hi,
I'm trying to use a Bulk IN endpoint (EPIN3) and am running into an issue.
I call the nrf_drv_usbd_ep_is_busy() function to test whether it is safe to proceed with...
Hello
I am using buttons less DFU,
S132_nrf52_6.1.1 softtdevice
using Android + nrf connecct, I can update the device with DFU
using IPhone 6, I can not update...
I am able to provision using BlueZ's meshctl tool on Raspberry Pi3. However, after restarting meshctl, I am not able to control my device. I tried the "connect" command after...
This isn't exactly a question, because after like...8 hours of debugging, I figured it out. However, in zephyr/samples/bluetooth/mesh, it defines a hardcoded device uuid ...
I am using ble_app_blinky_c application for my project. I want to update my central's default MTU size from 23 to 150 and I know my peripheral device supports MTU size of...
hi,
currently i am using maste r(nRF5_SDK_15.3.0_59ac345\examples\ble_centra\ble_app_uart_c) and slave (nRF5_SDK_15.3.0_59ac345\examples\ble_peripheral\ ble_app_uart ) example...
Hi
After migration from SDK 14.0.0 to 15.0.0 our FW crashes during SPI session
We use EasyDMA , so we use SPIM driver directly without wrapper nrf_drv_spi
The crash...
Hi,
The central part of multirole example is not able to connect to peripheral (other board with ble_app_uart peripheral) and error returned is in the on_ble_central function...
We're using LTE to communicate somewhat large data packets over MQTT, and we'd like to build in some robustness in case the link goes down or a publish fails to receive an...
as soon as I built and run my firmware program on SES ARM 4.22, RF connect scanner can find the ble device (NRF52832). But after 10 seconds later, i do rescan in RF Connect...
Hi, I need to activate uart on pca10059 i can't find where pin TX and RX in pca10059. i already read the schematic and try uart example but end up with can't send or receive...
