I'm looking for a good firmware engineer that can take my current firmware and add the buttonless DFU to it. I currently use the Keil environment but am open to switching...
I am working on PCA10040 board using Keil u5 debugger (V5.23.0.0, JLink setup). After accepting the continuous firmware update requests I get the error message "Missing core...
Hi,
I have just started using a nRF52840 PDK board with the purpose to verify BT 5.0 features. I am completely beginner working with nRF boards or nRF SDK. Anyways, I downloaded...
I have a USB host capable Android device running CentOS via Linux Deploy and everything is working perfectly except i'm unable to connect to my USB nRF24LU1+ Crazyradio PA...
Hi,
I am using multiperipheral mode in ble_app_hrs using the ble_app_multiperipheral example taking the functions on_connected and on_disconnected while connect and disconnect...
Hi,
I'm using nRF52810 on SDKv14.2 and I have changed the bootloader from 52832 to work for 52810. I could do OTA now. I found that the bootloader there is no timeout when...
Hi, Just to say that the nordic devzone website does not work with Vivaldi navigator For example, this link below opens correctly with my opera navigator, while it fails with...
Hello, we are trying to implement PWM function with an incrementing/ decrementing duty cycle using a logarithmic function rather than linear function. Is there any predefined...
Dear Sir,
I wanted to connect the peripheral device to a phone which has highest rssi value(where multiple phones will be sending requests).
For that I have enabled...
in Mesh SDK v2, simple on/off model example, client node doesn't act as a provisioner.
But I still want to combine provision & client in the same device.
Is that just...
Hi all,
I'm reading the ble_peripheral samples of the SDK. I know start a advertising with the function ble_advertising_start();
Now, i know a central address, then i want...
I'm using the PPI to generate a PWM signal on my nRF51822, and I've noticed that TIMER_SHORTS is never triggered unless the timer interrupt is also active. I had originally...
Greetings,
I believe I'm seeing the same issue as this DevZone ticket: https://devzone.nordicsemi.com/f/nordic-q-a/23903/gpio-behaviour-during-power-down-nrf52832/94059#94059...
Hi dear all !
the Question is very simply,
1. What the real RESET VECTOR (isr table) , ROM address for nRF52840 MCU ? I mean what happened each time after MCU CORE reset...
Using a nRF52832-DK and nrfconnect-2.0 on Win 10 everything works well.
But using that with Ubuntu 18.04 requires more installation documentation!
1. it seems, that the...
How many GPIOTE Tasks can I use at the same time. I want to drive six different pins with six different tasks which are connected to three events. Each event generates two...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
I have a peripheral (nrf52832) which is using a higher MTU (140 bytes). When I connect to it using the nRF Connect Android app, everything works. I can see the BLE_GAP_EVT_PHY_UPDATE_REQUEST...
Hi all,
I'm working with Nordic Thingy:52 (nRF6936 with nRF52832 inside).
Currently I'm working with original firmware (I mean, not modified firmware) version 2.1.0. But...
Hi,
I am debugging an SSD1306 OLED library, and in the datasheet, it does not explicitly mention support for repeated start bits. But using the nrf_drv_ API's with NRF_DRV_TWI_FLAG_TX_NO_STOP...
I would like to know what configurations are required to advertise long range.
Just changing the phy. returns error 0x07
I compared the ble_app_blinky and ble_app_att_mtu_throughput...
