Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm trying to use littlefs in Zephyr with SDK 2.7.0
My code is based on the example project "littlefs" and it compiles without problem using SDK 2.7.0
I'm using nRF Connect...
I am experiencing an issue with my board, where I have interfaced an nRF52840 with an LSM6DSV16 via SPI.
The nRF52840 chip, once started, can decide whether or not to...
I am trying to get an LED attached to GPIO to turn on. I have tried all documented methods I could find but with no success. I have no issue controlling the onboard LEDS but...
Having trouble creating the zephyr DTS DTSI files for i2c0 for the nrf54L15. need to get the initial definition correct,
actually using dtsi
& i2c0 {
compatible =...
Hi everybody. I'm using nRF Connect SDK 2.8.0. I've implemented Zephyr RTOS' core dump functionality on my project. I forced the SoC to write the core dump data on its flash...
I am working on a custom nRF552832 board. I need to use the reset pin (p0.21) as GPIO input.
I am using the NRFConnect plugin on VSCode to develop and program the board...
Hello,
We are using the nRF52840_CKAA_R7 package of the nRF52840 on our custom board. The USB pin connections are designed based on the nRF9160-DK's nRF52840 reference....
I would like to be able to open a bash prompt with the nRF Connect SDK (NCS) v2.0.0 toolchain environment loaded without going through Toolchain Manager ("open bash" option...
We are evaluating the nRF5340 chip for a Bluetooth LE audio broadcast streaming application.
Is it possible to use adaptive frequency hopping with the BLE audio network...
For the RADIO peripheral of the nrf52(840), if you set up the radio to receive coded Phy transmissions, I have the opportunity where I can set the MODE for 125Kbps or 500Kbps...
I'm trying to use nordic's BLE sniffer on a nRF52833-DK. I have programmed it with the firmware "sniffer_nrf52833dk_nrf52833_4.1.1.hex".
I've then tried both the command...
When I use nRF Programmer on my laptop (v3.0.7) to update firmware on my Thingy53 with a USB cable and SW2, the programming seems to finish normally, but it prints "Bluetooth...
Hi, I'm having Bluetooth LE peripheral nus code which works fine with v2.7.0 with nrf52840DK (I can connect with an Android App and stream data etc): Changing the build configuration...
NCS 2.7
NRF52840
Building with sysbuild, MCUBOOT, and 2 different applications (mfg and end-user)
My custom board includes a sensor fusion IMU from bosch. The firmware...
