Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
I am new to nrf52832 development. The question is that:
I want to do m ultichannel(4 or 5 channels) ADC in scan mode every 1s. and the MCU consumes ultra low current(3-5uA...
As the subject suggests. It is a simple question. I only see development boards with NRF53, but we decided to go with NRF54 in this project. We need BLE and WiFi on the device...
Dear Nordic experts,
I am looking for which CMSIS version are used in nRF5 SDK versions. For instance 17.1.0 uses CMSIS 5.6.0. But I cannot find which CMSIS version is used...
I am trying to retrieve the PIN / HWID required for nRF Cloud onboarding using the AT command AT%XDEVICEID , but I am unable to get a valid response from the modem.
However...
Hewy there:
I have a custom nRF52833 board with NCS v3.1.0, using ESB and USB CDC ACM. The external 32 MHz crystal is oscillating fine — we see a clean 32 MHz sine wave...
Hello,
NB-IoT RRC Connection Re-establishment is supposedly available on nRF9161/51. Is there a related AT-command to enable / disable?
Best regards,
François.
Hi all,
I am using a tagconnect cable to flash my custom boards using a devkit. I was able to flash 4/5 boards. I first recovered the locked factory boards, and then flashed...
Hello.
I am experiencing an issue where Mesh communication fails after connecting to the SMP Service in the Bluetooth Mesh DFU Distributor sample.
Environment:
NCS...
Hello ! I would like to know if the nrf52840 is affected by the errata https://infocenter.nordicsemi.com/topic/errata_nRF52832_Rev2/ERR/nRF52832/Rev2/latest/anomaly_832_149...
Hello,
I am working with the nRF9151 DK and NCS v3.3.0 . I am experiencing a critical modem fault at startup.
Problem Summary: When I start debugging, I immediately get...
I attempted to conduct Bluetooth development using the nRF52840DK (NCS 3.2.0), but I encountered an MPSL error:
ASSERTION FAIL [0] @ WEST_TOPDIR/nrf/subsys/mpsl/init/mpsl_init...
Hello,
I am trying to add different ConcentrationMeasurement cluster types to my application (CarbonDioxide, VOC, Pm1, etc.) but have an issue with zap-gui not saving the...
Good day,
I have been making use of the nRF54LM20A SoC with ncs v3.2.0. I am currently trying to use the high-speed SPI (SPIM00) lines on Port 2 to communicate with an SD...
