Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hi,
I am using nRF7002 DK to develop MQTT + I2C sensor. The following are my steps
1. use samples/net/mqtt as the base architecture, everything running well ( I don't...
Hi
From the past few days, I have been trying to perform FOTA with BLE using external QSPI flash. However, I'm unsure if I'm creating the proper files and adding the correct...
Hello, I'm starting to study MCUboot with the intention of implementing firmware upgrades in a product. I'm currently working with the nrf5340dk eval board. As far as I understand...
Hello, I am porting my projects from NCS v 2 . 6 .0 to v 2 . 7 .0 and I am defaulting my builds with sysbuild enabled .
I have a project that has FLASH enabled but doesn...
If you run the exercise 1 code as-is (with the lines from the course materials added) it will run out of sockets and fail within a few button 2 presses. The problem is that...
Hi, I'm using nrf5340 DK. I am developing a device that needs the nrf chip to simultaneously recieve audio from a device and send sensor data back to the device over BLE....
I'm changing and testing my code with nRF52832 by NCS.
When I try to connect ,I will get those information.
SEGGER J-Link V7.94e - Real time terminal output SEGGER J-Link...
Dear Team,
into the Connection parameters chapeter of the Lesson 3 is stated that
The relation between data length and MTU is not one-to-one. On air, the data length can...
Hi Nordic Champs
We have developed a nRF52820 based USB dongle board, as attached. It will be open source hardware soon. [ have attached pics]
Would like to know if...
Good morning, I've been trying to evaluate the Thingy91 with the asset tracker v2 firmware but I wanted to connect it to our own AWS so I needed to compile the asset tracker...
I am using an N52811 QFN32 on a custom board.
I modified the SAADC sample as follows and ran it on this board. (3.0V was input to AIN2.)
However, p_event->data.done...
When I launch the Power Profile in nRF Connect for Desktop, the following log appears, and it cannot connect to the PPK:
The versions of each application are as follows...
As the question explained. I want to know if we can implement all three zigbee roles viz, Edge, Router and Co-Ordinator in a single project and can be able to switch them...
