Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
I'am working on nRF52840-DK and nRF9160-DK.
i'd like to add an interrupt pin for a SPIM device. (eg. in the following spi_dev: )
&spi3 {
compatible = "nordic,nrf-spim...
Dear nordic team,
i want to take log from dfu example i tried using rtt veiwer but it doesnt work.im using sdk version 17.0.2 and soft device 7.2.0 and nrf52840 DK
in...
Hello ,
I am using nRF52832 , sdk 16version. I want to set the BLE connection interval via BLE command using application. How to do that? I tried to assign the variable...
Hi,
I’m using the nRF SDK 1.6.0 and trying to build the “ memfault ” sample for nRF9160 using the
“ nrf9160dk_nrf9160ns ” board. The sample location is:
C:\Users\username...
Hello, after I make the connection to the nrf device with the phone, I found there is only a "Forget This Device" option on its setting page. So is there a method such as...
Hi Nordic,
The bluetooth qualification needs the information of nF5340's value n for Intermodulation test but hard hard to find in any document.
Please help us out, thank...
Hello,
It appears that when the project is generated it is expecting a "../common" directory?
CMake Error at /opt/nordic/ncs/v1.7.0/zephyr/cmake/kconfig.cmake:209 (message...
Dear Sirs,
after "few" hours of testing, I noticed that nRF9160-DK loaded with SLM v.1.6.1 is not working the same after awakened up from sleep (#SLEEP=1) or even from idle...
Hi everybody,
I have developed a project where a central device with multilink, connected to the maximum peripheral as much as is possible (in my case 4 devices more). ...
Hello,
I'm trying to figure out how to get A-GPS data via a GSM modem in places where LTE-M is not availalble.
Does the SUPL library support this, if I populate supl_client_ctx...
Hello all,
I just found out that the nRF Connect extension for VSCode has been release, which is great news. Good job Nordic Team! I have followed the steps described in...
Hi, dear Nordic.
I'm using BC805M Module which uses nRF52805 SoC. What's the max sink/source current for individual pin OR total chip, please? Where could I find relative...
Hi,
Im using nrf9160 based custom board, nrf sdk 1.5.1.
I want to get the time from NTP servers, for that i connected to CATM1 n/w, connected to NTP server using UDP Protocol...
Hello, I am working with custom board nrf52840 and SDK 17. I am doing some changes to the project and I am getting an error that the SDK is using VFP register arguments but...
Hi,
I am getting this error message when using the nRF52 dev board but not when using the nRF51 dongle. I receive few packets and then it disconnects with this error message...
