Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image. I am using ‘ble_app_blinky’.
As shown in below snapshot I am just doing below...
According to the blog below, hardware design of nRF9160-SICA has been fixed on May 31st. https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog/posts/nrf9160-development...
I am designing a pcb just the nRF 52840 MCU. The design of the PCB is based on the reference design from Nordic. When ordering the PCB I came across a problem that the vias...
I have 4 gpio inputs on the nRF52840 working and sending these states over the BLE. I tried to add a few more gpio inputs but I get an error =4 which I think is NRF_ERROR_NO_MEM...
Hello,
I can successfully put my nRF52832 into System OFF mode, however, the Debug Mode Interface is still running, so the current consumption is > 2mA. What are the command...
I have a nRF9160 DK need to update modem firmware to v1.0.0
According to C:\nRF91\mfwnrf9160100\README.txt below, I should use nRF Connect Programmer to update modem firmware...
In the light_switch example of nRF5_SDK_for_Mesh_3.1.0, I noticed that generic_onoff_client.h has a union for holding the current message packet. However, there is only one...
The timer example with SDK 15.0.0 uses the old timer driver. Is there any example code showing how to use the current nrfx_timer?
I'm just trying to generate a periodic...
Hi Nordic team and fellow fans,
I am trying to switch from SPI to SPIM and getting an odd assertion with no context after I kick off a SPI operation, but it only happens...
SDK15.3.0
nRF52810
the original secure_bootloader and buttonless_dfu works fine.
nRF5_SDK_15.3.0_59ac345\examples\dfu\secure_bootloader\pca10040e_ble
and nRF5_SDK_15...
Hi,
I am using the nrf52832 dk,
i want to decrypt the data i receive over ble (AES encrypted data will be sent over ble) which api's or sample codes should I use?
Hi,
In the cops=0 state, how long does the modem take to scan each band of both cat-m1 and NB-IoT? How does a roaming sim affect these times for both technologies? In...
Hi
I would like to give a try to nrf52 on mbed. So I went to:
https://os.mbed.com/teams/mbed-os-examples/code/mbed-os-example-blinky/
and clicked Import to compiler...
The demo board would not connect (no second LED)
Since in Italy we only have NB-IoT, I guess I should recompile a more recent version of the demo application.
I have followed...
I'm a newby in bluethoth communication. To control model cars and model trains in scale 1:87 I built a decoder with an ATMEL chip. The communication based on digital infrared...
