Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Dear all,
I am trying to program a chip using an st-link v2 connector.
The chip is nrf52832.
Although I am able to upload hex files that come with the SDK examples...
Hello, I am using a nrf52832 Soc for my development. I follow this https://github.com/bjornspockeli/custom_ble_service_example for the custom BLE service. I can do a specific...
Hi,
I am using nRF52840 Preview-DK with SDK v15.3.0
I am using the serial library to write to UART 1, while writing all goes well while I write less than 255 bytes...
Hi,
In the nus example of sdk 15 the device does not advertise if i comment out the uart_init() function. Why does this happen?
What is the relationship between the uart_init...
Hi guys,
After i provision for client node or server node by smartphone i have unicast address for server model or client model. How can i send message from client to server...
Ubuntu 19.04
SDK 15.3
nRF Connect v2.7.0
Nordic_HTS example both pre-compiled and self-compiled
Uploading to Fanstel BT832F and nRF52 DK
When I upload the example...
Hello,
My goal is to send a binary file by Bluetooth into the nRF52940 board from the terminal. I saw the ble_app_uart example. It seems to be exactly what I want to do...
Hello,
I need to use USB 2.0 connection as a USB MSC device as well have it communicate over a USB 2.0 connection to a Wi-Fi module.
I know there is a USB 2.0 built into...
I'm working on a project using nRF9160 DK.
How can you use MQTT+TLS in nRF9160?
Where should ca certificate file be stored?
I modified the code below in mqtt_simple...
hello i am using nrf52832 DK and working UART_APP_BLE , i want know where the data will be stored when we send any message through mobile to the device. can we see the received...
Hi, I am new at programming.
I am trying to program nRF51822 DK. But My Desktop can't appear J-Link Debugger as a USB drive.
I read some posts about that but I didn't...
Hi .......Clan
I am planning to make chatbox mean chatting (transferring the messages) between the central and peripherals even peripheral to peripheral , and device peripheral...
Im using MCP6S21 amplifier which takes input from some I to V converter and output of amplifier is connected to nrf52832 via I2C pins so how to change or vary gain of amplifier...
I am having a problem running MQTT_Simple on my nRF9160 DK.
The COM Port shows the following:
***** BUS FAULT ***** Precise data bus error BFAR Address: 0x4002a514 **...
