This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I am trying to use a nordic thingy52 to read the sensor values off the device and relay the values onto a wirepas network. I have found the sdk and unpacked the following...
I'm just getting started with this device, trying to see what it can do. I've inserted the SIM, and set it up to show up in nrfcloud.com. What worries me is that the location...
Hi Support,
I am using
I have my own customized board with nrf52840 . i am using SDK v15.0.0 with Softdevice verison v6.0.0
I am advertising with DFU and NUS services...
Hello,
I used the uart example to print text over serial communication from the SDK v11.
The problem is when I write lot of text consecutively, I don't receive all data...
i use the BLE uart example to test. I delete the UART hardware init and just use the BLE send data to phone every 500ms. I found whatever i set the MIN_CONN_INTERVAL and MAX_CONN_INTERVAL...
Hi,
Some time ago I ask a question about changing the publish address of a node in the mesh locally. I received the answer in the following threat and verified it:
https...
Hi All,
I used the app "ble_app_uart" and "ble_app_uart_c" on two custom boards mounting a n52840 QIAACO.
I know that in the app (nRF5_SDK_15.1.0_a8c0c4d\examples\ble_peripheral...
Dear Sir/Madam,
I want to measure the data speed between two BLE 4.2 based devices and two BLE 5.0 based devices.
Using nRF52 products for this purpose.
Kindly help...
I know that the nRF52832 is strictly a 3.3V device however, I was wondering whether any of the GPIO pins are 5V tolerant?
Is there any internal clamping diodes within the...
Hello,
I have noticed, that https://github.com/NordicSemiconductor/nrfx was updated with a nfct driver. I am trying to extended the nrfx port on micropython (see https:...
Hi,
I'm trying to setup the Peer Manager on a nRF51822 with installed the S130. I'm working with Eclipse where I installed the 12.3.0 SDK.
At compilation time I get the...
Hi, I have a two part question, I know the NRF51822 (and I believe all 4.0 BLE chipsets) are being sunset, when will this start taking place?
Since I'm currently using the...
HI,
i am using nrf51422 with sdk13.3.0 and soft device 130
i am receiving 69 byte of data through UART, i am compressing data in two packets. here after transmitting a...
