Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
i need to meassure Digital ports when i am in __WFI (); I noticed that WFi will hold the CPU so how would it bee possible to to react on digital Pins? Is it possible...
Hi
The bug can be found by following the below steps.
Pair nRFready keyboard (Desktop 2 v1.0.5) to Windows 8 BTLE host. The keyboard can work.
Disable Windows...
Hi ,
Here is my code used to write in to non volatile memory.
#include "nrf.h"
#include <stdint.h>
#include <stdbool.h>
#include "nrf_nvmc.h"
static void flash_page_erase...
Hi all,
I can see the DFU project in SDK and know that the device firmware can be updated by using BLE and UART.We just use the 2.4G to do the airplane model.But I donn...
Hi ,
Here is my code used to write in to non volatile memory.
#include "nrf.h"
//#include "uicr_config.h"
#include <stdint.h>
#include <stdbool.h>
#include "nrf_nvmc...
hi,
i want to get the Email,MissedCall,Other(SMS) from Apple(ios7) to my device.
i survey that , ANCS(Apple Notification Center Service ) at the the Latest iOS7
and access...
Hi
I'm using the nrf51822 with Softdevice S110. I want to find out why a pairing has not worked, PIN-Code was wrong, PIN-Code timeout.
Which events I can use for that...
Hello,
I have tried the nRF51822 SDK example , "ble_app_hids_keyboard", it can send text "hello" to iPhone. When I cut off the power of the nRF51822 and turn it on again...
I have nRF8001-DK and Arduino Uno. ble_uart_project_template from nRF8001 SDK for Arduino (Bluetooth_low_energy_for_Arduino_0_5_0_0_RC2) was used. It was used with Master...
Hello,
i create a custom profile with two services and with 30 characteristics. The first service has 29 characteristics. Up to this point everything is ok, but when I...
Hello, i would like to know if its possible to use your SDK tools (S110 Soft Device, nRF51 SDK) without your evaluation/development kit.
Since RFduino has a RF51822 chip...
Hi, I try to create a iBeacon tag with NRF51822 for Apple device, but it seems not to work, yesterday I update the newest SDK, I found the ANCS was added, so Nordic also can...
Hi,
i have a big Problem, if i debug my code i get in some cases in register 3 the value 0xDEADBEEF and after that the device doesn't work any longer in a correct way....
Hi
I can use the duf_dual_bank_ble to do the OTA,but I donn't know how to use the dfu_single_bank_hci to do the OTA.Could you give me some
advice about it?Thanks.
Hi.
I have a problem with writing value to gatts attribute when device is in connection mode. In my application I want to check if the parameter writing by the client to...
