Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hi,
I'm working on getting the DFU bootloader working and I'm following this blog post.
I'm successfully compiling and loading the bootloader to our custom hardware...
I want two pwm channel output 1MHZ frequency, the phase difference between two PWM channels is 180 degrees。when i set two pwm frequency to 500KHZ, use the configure below...
Hi,
We are testing an evaluation board nRF9160-DK with the firmware samples to build our own prototype. Is there a friendly process or example for FOTA to update the device...
Hey
I would like to know how can i connect 1 peripheral to multiple centrals(ex : 2 centrals), I am have three nRF52 DK boards for two centrals and one peripheral, My idea...
Hi,
Currently I am adding DFU support to our application, I was able to compile the secure bootloader example and use it.
my next question is, how do I enter DFU mode...
Using Rowley Crossstudio for ARM.
Using SDK V15.3.0 and S140 V6.1.1
When calling sd_softdevice_enable(..) it returns 0x1001 ( SVC handler missing ). Any suggestions ?
Hello Nordic Support,
Using the Nordic Power Profiler Kit v2.6.2, I can get the average current consumption for a maximum window of 120 s. Is there a way to get the average...
Hello Nordic Support,
Using the Nordic Power Profiler Kit v2.6.2, I can get the average current consumption for a maximum window of 120 s. Is there a way to get the average...
At present, I have a project that needs to add dual uart function, but 52832 does not have hardware dual uart function, so I need to simulate one serial port, I need your...
Hi all. I try to implement ble dfu bootloader project via getting start from SDK/examples/dfu/secure_bootloader/pca10056_ble_debug project.
Using:
OS: Linux
Compiler...
Hi!
This is a general question about iOS app distribution, but it regards our use of Bluetooth Mesh. I know it is each company's own responsibility to make sure they comply...
Hi there,
I am porting existing code from nRF52832 to nRF52840, and found that bootloader references to NRF_BPROT fail:
Apparently becuse the nrf52840.h in the mdk does...
Hi All,
I have loaded in the Bluetooth Mesh Light-Switch example and it works well.
For now, I would like to read out the received data from the switch node (client) to...
Hello! I am using SDK 15.3.0 to develop the NRF52832 firmware. At present, I want to implement a function, when the device is connected to the IOS host, start pairing, and...
