hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Hello,
I really need the ability to switch between different advertising messages. Could you please (please!) add a callback after an advertising message has been sent...
We are using the NRF board to act as node.
Samsung Galaxy S6 device is being used as the Router. We are trying to ping the node using ping6 command.
The issue is that the...
I have a working peripheral NUS application to pair/bond by entering passkey in the nrf master toolbox android application.
Now i want to replace the mobile witha nrf 51822...
nrf51822bluetooth low energycode 10
twiddle gravatar image
twiddle
1
asked May 9 '16
I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just...
Hello Everyone,
I am designing the prototype using NRF51822 and i have choosen the DC DC power mode but the real problem is most of the time my radio will be sleeping so...
I have nRF52 Development Kit (PCA10040). I'm using Keil uVision.
I want to measure RSSI of some beacons and if the signal is strong then send MAC of this beacon over UART...
Hello Everyone
I'm trying to debug ble_app_beacon project, having the following error when trying to launch the debug session:
Error in final launch sequence Error executing...
Dear Sir:
I have a (BLE + 2.4GHz)Mouse project, But now I had some problmes. Please help deal,
Thank you so much Sir.
a). My program modification base on "nrfready_desktop_2_v3...
Hello all,
Just to note any versions that need saying, I am using
SD 110, V8
The 10.0 SDK, freshly unzipped
The dual bank BLE bootloader, unmodified
Arm...
I was looking at this PA/LNA example: here . I noticed something I'm not sure about, so I was hoping someone could shed some light on this.
In the diagram shown in the...
I've been working on a project, which requires data transmitted through ble to cell phone app. The user could acquire the data from the sensor when he sends a specific string...
Hi
We use the NRF51 in a mesh sensor network. We noticed in a trailer suited for cold chain transport (double metal walls with thermal isolation between) that the radio...
Hi,
I have problem with ble_nus_c.c in SDK v11...
Normal operation is:
Connecting to target 57E19A190FDF
Connected to target
[DB]: Starting discovery of service...
When I used the demo of ble_app_hrs_rscs_relay,I cannot write the bonding information to the flash.
I connect to the board by my phone.I cannot find the information about...
