Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode,and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
Hello,
After searching in forum, I understood that we cannot debug application with softdevice unless PRIMASK bit is set.
But in my application there is a requirement...
Hi Nordic
I am using GZLL to develop a prototype whereby data from sensors will be transferred to a Computer in a Wireless sensor network.
The idea is, when data are requested...
Dear all,
we want to use a nRF52837 for a developement project we are planning. We have been asking ourselves on which functional level the alpha Softdevice S132 for the...
Hello, i analyze the device manager routine (device_manager_peripheral.c) and in BLE_GAP_EVT_CONNECTED case you checking containing the device address in bonded table.
My...
I am working with nRF51822 beacons and an iOS 9 application that I am developing. I am testing on an iPhone 6. My application uses the CLLocationManager's beacon ranging functionality...
Hi,
I want to use the whole payload of the advertising packet. I decided to use the manufacturer specific data. BUt I cant´use the whole payload by myself. I get this payload...
dear all:
I use the spi slave mode. i have a question,pls help me.thanks.the questions as follow:
I want to distinguish instruction type, and then reply to the corresponding...
Hello,
I am working on nrf51822 SDK 9.0 and softdevice 8.0 . I got the application note to create a custom profile for SDK 5.2.0 and softdevice 6.0.0 in nAN-36_v1.1 . ...
Hi: We develop our program based on (nrf51822 QFAAG0 1403AL), I found a serious problem that our new IC is (nrf51822 QFAAG2 1415AF), and the old program can't run on it any...
Not sure where to post this...
but there's a minor bug in components/toolchain/system_nrf52.c, where NRF_UICR->PSELRESET[0] is being checked twice to see if a reset pin...
While ota dfu via nrf toolbox android app, it sends wrong (0x15918) image size in start packet, and also bootloader starts writing softdevice image at address DFU_BANK_0_REGION_START...
Hi! I want to make a BLE network with 1 master (nRF51-DK) and multiples slaves (nRF51-dongle). I`ll send differents commands from master to slaves. This is for home automation...
Hello,
I am writing an application using SDK version 8.1 where I have a pin using the PORT event in nrf_drv_gpiote library. I have a need to disable the event temporarily...
I am encountering a problem with GPIOTE PORT events on the NRF51422 in a custom design. The chip occasionally seems to be able to get into a state in which the registers are...