hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
The pwm library seems to add 10KB worth of code to my program. Alot of it probably comes from the nrf_drivers that are used, but still 10KB. While enabled it seems to pull...
Hello,
Since 2 weeks, I use heavily my nRF51-DK (PCA10028), with mbed compiler to make a BLE enabled device.
But, since few days, when i have tried to cut the SB9 in order...
I have a Rev3 nRF51822 chip (CFACA00) on a custom board (no external pull resistors on SWDIO or SWCLK), and I am using nRFgo Studio 1.20.0.2 to program SD 8.0.0 and my Nordic...
I'm using Python bindings 0.5.0 and the connectivity app. On one of our machines that is running tests with the satck/dongle we see it fail a lot with a scrolling of this...
I want to extend the ble_app_multilink_central for pca10028 Example to be able to communicate with a sensor via SPI and then initiate a connection with another pca10028.
...
I'm trying to discover a vendor specific service that has 7 characteristics. However, when I increase BLE_DB_DISCOVERY_MAX_CHAR_PER_SRV to 7 , ble_stack_init() hard faults...
Is it possible to use PPI and RTC to turn the HFCLK on or off ? (external Xtal)
Example - something like this ...
NRF_PPI->CH[9].EEP = (uint32_t) &NRF_RTC0->EVENTS_COMPARE...
hello,
when I use the chip nrf51822(3rd generation),I find that when I open DCDC function,the ability of chip receiving msg is weaken.the receiving distance is shorter a...
I am doing a blob read on two s130's with s120(central). I am getting BLE_GAP_EVT_CONN_PARAM_UPDATE event while doing a continuous blob read.
Some times i get BLE_GAP_EVT_CONN_PARAM_UPDATE...
Hello,
Can you please provide full schematic for nRF52 dev board. I looked though the documentation and there are small bits of the schematic, but I didnt find full sch...
Using a nRF51822-QFAC-A1 on the nRF51-DK I noticed unexpected behavior when starting the HFCLK and LFCLK in rapid succession. This variant reproduces the problem at startup...
