hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
I'm trying to figure out the RAM power and RAM retention on the nRF52. This is the micro I've used that has had the ability to turn chunks of RAM on or off.
Here's my understanding...
I'm trying to apply a firmware update using a zip file that has worked with older version of nRF Toolbox. Using the current version, (4.1.1) on iOS, I select DFU, then select...
Hi everybody.
I am opening a dedicate question after a recent topic that already helped me a lot, with another discussion pretty similar to my problem. Resuming briefly...
On the nrf52dk development kit, I want to power the target nrf52 from an external supply without powering the interface mcu (the debugging probe). How do I wire that? I don...
I'm trying to add nRF_Drivers files to Segger studio project, based on nrf51,51422(10028) examples. I added path in preprocessor user definitions and I added file like nrf_drv_lpcomp...
I set up my PWM Driver like this:
nrf_drv_pwm_config_t const nrf_drv_pwm_config =
{
.output_pins =
{
BSP_LED_2 | NRF_DRV_PWM_PIN_INVERTED, // channel 0
NRF_DRV_PWM_PIN_NOT_USED...
Hi,
I would like to test my C code with bootloader over air by BLE. I am using nrf51822 with soft device 110. Does Nordic Company is sharing any application which can bootload...
So this might be one of the most confusing issues i've come across sofar. We're currently developing a product based on NRF52 (more specifically NRF5283 QFAAB0) with a custom...
Is there firmware available as binary file that can be loaded to the nrf52832 that allows connectivity to is as a UART HCI compatible device?
Would the same firmware be...
Hi,
I am using "nRF Toolbox -> DFU" to change an application on my BLE module which contains; nRF52 device, SDK->v11.0.
I am using ".hex" file to load the application...
iphone5_b.psd m370_android6_b.psd long_write_error.png I using SDK11. I porting nus profile to my system and make a customer's UUID. I use Lightblue on iPhone 5 to connect...
Hi,
I would like to know, by using nRF528322 Development Board can we dump the code into another hardware like custom nRF51822 microcontroller..??
If Yes, What are the...
hi , need a urgent help on small problem but really not getting ahead bcos of it.
I'm using NRF52, SDK v11 , Software Device s132.
I'm calling sd_ble_gatts_value_set() like...
The struct type nrf_saadc_config_t is defined in ../hal/nrf_saadc.h but is not referenced anywhere else in SDK v12. Thus it is either cruft, or more likely, the function nrf_saadc_init...
