Hi,
We designed the circuit followed the reference circuit(QFN48), but we always failed in the 8kv ESD test.The CPU always reset while ESD testing.
The 8kv ESD power...
Does anybody got an app inventor2 "project" to communicate with the (Adafruit) Bluefruit LE UART (or SPI) ?
Note: my Android version is 4.4.2 (LE "advertising" not supported...
I've created a Secure DFU client using the multilink central example with S130 and SDK 12.2 (running on PCA10031).
There are a few issues we have trouble with.
The...
Hi,
After successfully managing to preserve our devices bonding information (and custom app context data) across DFU updates, we have a few related questions.
I should...
I would appreciate some suggestions on a good development flow to go from an Example to end application
I have nrf52832 on a custom PCB.
I tested several sdk13.0.0 examples...
If anyone will ever have this error:
When using c++ and singleton the use of operator new is not possible.
I found the solution in this post: forum.arduino.cc/index.php...
Hi I am using Jlink board, when connected to my pc, I can't select nRF5x programming.
Version I am using is 1.20.0.2. I tried the uninstalling everything and installing....
I used nRF Mesh app both iOS and Android versions to communicate with
nrf5_SDK_for_Mesh_v2.0.1_src\examples\light_switch\client
and
nrf5_SDK_for_Mesh_v2.0.1_src\examples...
The system consist of two nRF52832, one acting as SPIM and the other one as SPIS. I hace created a while loop always asking for certain amount of bytes but the MISO line on...
Hello, I am new to nRF micro-controllers and using Netbeans. I have cloned the repo of a project I would like to run, which builds successfully, and am getting the following...
Two questions. 1) What is the point of the watchdog ISR? In the Ambiq Apollo 2 microcontroller, the watchdog ISR fires and if the CPU doesn't pet the watchdog slightly after...
Hello I have problem with Mesh Serial Example and Interactive_pyaci, it works just in Debug-Mode. I use nRF52840, nRF5_SDK_15.0.0_a53641a, nrf5_SDK_for_Mesh_v2.0.1, Python3...
Hi I am trying to optimize my nrf51 app for low power. However I can just reach 0,500mA when just advertising (advertisement only is ok for me). Do you know or do you have...
I am trying to integrate the NFC read/write functions in my BLE application. I have used the writable_ndef_msg project functions to start with. The project on its own works...
Hello
For my final year project at Varsity I am creating my own smartwatch + edge computing IoT system. The watch and infrastructure needs to be as low-cost as possible...
Hi,
I am using a nRF52 DK board and programming in python.
After performing a successful DFU over BLE i want my Target device to be disconnected from the nRF board so...
thanks for the answer on the previous post.
What I came to know from our firmware engineer was that your initial version of the Android app could not support
1. multiple...
I want to know 2 things about the nRF Mesh app:
1) Is it possible for the Mesh app to provision non-proxy nodes via the proxy nodes?
2) I think it's possible to subscribe...
I have a project using FreeRTOS with Tickless idle enabled, SDK 11.0.0 alpha and the S132 soft device. Currently the project is consuming ~6.5mA average, ~5.2mA if advertising...
Hi There,
I very new to Nordic BLE application and was looking for method to combine ble_app_beacon and ble_app_blinky togather and having both switching and running at...
Hi:
In the datasheet, there have a description
Input range = (+- 0.6 V or +-VDD/4)/Gain
for a example, if Gain = 2, reference = 0.6V,
input range = 0.6 / 2 = 0...
