i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hello,
I'm trying to use the Arduino BNO055 shield with PCA10040. This should be quite easy....but it doesn't work: I can't get any acknoledgement. Arduino use 5V pins,...
Hello,
I habe got a nRF52840-Development Kit. It is Herdware Revision 1.0.0.
While going through the Getting Started i find that the LEDs do not flash and that i have...
Just a heads up for anyone who bumps into this and is scratching their head. If you have ninja version 1.9.0 installed your build may hit an error with messages like this...
Hi everybody,
we have a remote control based on the nRF52832 and are experiencing a wierd issue with notifications.
We are using a custom 6 byte payload keymap characteristic...
Hi all, I use NRF52832.
I have a problem. I want when I connect to my chip and bond. After bond success, I insert new service. And when I disconnect from my chip, new service...
On page 69 of nRF52840 Product Specification 1.0 4413_417 v1.0 / 2018-03-16:
The table in section 5.3.6.8 shows that the WDT is NOT reset from a Wakeup from System OFF mode...
Hello,
We have an application based on ble_app_blinky that is actively scanning for advertised packets but does not attempt to connect. We have a second application based...
Hello,
i am using nrf52832. i am using 8 different pin as a 8-bit parallel port.
in my process i have to read each bit from each pin then converting those bit into byte...
I am using an nRF52840 DK. The software I have in it is emulating an NFC Type2 tag and is implementing a BLE peripheral.
When the device starts up everything works as expected...
Good day!
In SDK 12 I read values using this code:
and handle value in ble_evt_handler:
This works fine, but using SDK 15 this code crashes with fatal error...
This application uses a Rigado nRF52840 module to collect SPI data from 2 peripherals in slave mode. I have been unable to get the SPIS example running in the target board...
Hi,
This is a really weird problem.
======================
Setup of 52832 hardware:
- Custom board, using 32MHz XTAL and LF RC.
- SDK15.2, S132 610
- Segger RTT...
I need a 30 second hardware based interrupt for a Nordic BLE nrf52832 chip running S132 Softdevice. I would like to use RTC2. This will be used to run a short BLE ad scan...
