Hello,
i have read all posts about writing to FLASH when using BLE. But could not find the desirable method.
What i would like to do is to write to flash from characteristic...
I'm trying to add the product key it shows an error "can not the product to your list" and therefore i will not able to access to the User guide
Thank you
hello, im from india im using nrf24l01+ for my project to transmit and receive data between two arduinos. i tried all tutorial basic programs but i cant sucessfully send and...
I'm analyzing app_timer scheduling code..
I have an question about list_insertation_handler function in SWI0_ISR
I think if ( (p_timer->ticks_at_start - m_ticks_latest...
I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hello,
I'm trying to use the Arduino BNO055 shield with PCA10040. This should be quite easy....but it doesn't work: I can't get any acknoledgement. Arduino use 5V pins,...
Hello,
I habe got a nRF52840-Development Kit. It is Herdware Revision 1.0.0.
While going through the Getting Started i find that the LEDs do not flash and that i have...
Just a heads up for anyone who bumps into this and is scratching their head. If you have ninja version 1.9.0 installed your build may hit an error with messages like this...
Hi everybody,
we have a remote control based on the nRF52832 and are experiencing a wierd issue with notifications.
We are using a custom 6 byte payload keymap characteristic...
Hi all, I use NRF52832.
I have a problem. I want when I connect to my chip and bond. After bond success, I insert new service. And when I disconnect from my chip, new service...
On page 69 of nRF52840 Product Specification 1.0 4413_417 v1.0 / 2018-03-16:
The table in section 5.3.6.8 shows that the WDT is NOT reset from a Wakeup from System OFF mode...
Hello,
We have an application based on ble_app_blinky that is actively scanning for advertised packets but does not attempt to connect. We have a second application based...
Hello,
i am using nrf52832. i am using 8 different pin as a 8-bit parallel port.
in my process i have to read each bit from each pin then converting those bit into byte...
I am using an nRF52840 DK. The software I have in it is emulating an NFC Type2 tag and is implementing a BLE peripheral.
When the device starts up everything works as expected...
Good day!
In SDK 12 I read values using this code:
and handle value in ble_evt_handler:
This works fine, but using SDK 15 this code crashes with fatal error...
This application uses a Rigado nRF52840 module to collect SPI data from 2 peripherals in slave mode. I have been unable to get the SPIS example running in the target board...
Hi,
This is a really weird problem.
======================
Setup of 52832 hardware:
- Custom board, using 32MHz XTAL and LF RC.
- SDK15.2, S132 610
- Segger RTT...
I need a 30 second hardware based interrupt for a Nordic BLE nrf52832 chip running S132 Softdevice. I would like to use RTC2. This will be used to run a short BLE ad scan...
