I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
Dear all
I am currently working with a nRF52840 Dongle, the ble_app_blinky_s140 example.
To power some external circuits i have to set VDD to 1.8V.
Until now i tried...
hi, this is Shivaji, I have to work on Bluetooth mesh, so which kit I have to buy, can I buy thingy52 or can I buy nrf52dk. which board should I buy, and can get the android...
Dear Sir,
I have bought a BMD 300 chip.
I have implemented a firmware with segger embedded studio and SDK15 for nrf52832.
I have flashed it to BMD300 DK from Rigado...
Hi:
As we are going to use nRF52840 on our product, we were trying the check the HW security implemented in the chip. nRf52840 implemented Arm TrustZone CryptoCell-310 in...
Hi Team,
I hope you are doing good.....
I am using nRF51822 with the SDK version 12.3.0 in windows, keil version is 5.26.
In the blu_app_uart Application i want...
Hi,
In order to isolate the issue, I've created an app that :
1. switches to dc2dc mode.
2. calls sd_app_evt_wait()
I still see 3ma consumption,
any ideas...
Hi
Actually i have a big project and have a problem in the estimation of FLASH and RAM memory for the project
i ma going to implement the mesh SDK with the BLE Stack because...
Hello,
I am working with a custom board with the nrf52832 chip.
I have merged and written the following on the board: SD (s132, 6.1.0) + secure bootloader from the latest...
Hello,
I purchased a nRF52 DK board and sparkfun nrf52832 breakout board , and was successful with blinking the LED on the breakout board.
In order to test if I would...
Hello,
(I am using SDK 15.1 on a linux system)
I will breakdown the question in two parts -
when do we get fatal ? - i know one or two cases for example when softdevice...
Hi.....
i want to transfer the data for every one minute from peripheral device to nrf connect via (phone app).. how to declare in the program and what function to be used...
Dear all,
When I added more than 4 buttons by modifying the example "ble_app_uart" of nRF5_SDK_15.2.0_9412b96, nRF52832 can not run normally.
Another strangely problem...
Hi,
Just got four 52840 USB dongles, with the intent to evaluate the Nordic BT Mesh. But I've been unable to get even a simple Blinky example programmed on the dongle. I...
