I'm analyzing app_timer scheduling code..
I have an question about list_insertation_handler function in SWI0_ISR
I think if ( (p_timer->ticks_at_start - m_ticks_latest...
I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
When I debug my product ,using nrf51822, using the ble_uart example, my product will using MCU commnication with BLE,using uart.
When I modify the PIN of the uart TX pin...
Hello:
I am working with my sales contact at AT&T in the USA. I mentioned this module and that it was going through certification. Before I moved forward with the carrier...
Hi,
I'm using an nRF52840 dongle with pc-ble-driver on Linux. It has connectivity 6.0.0 with S140. I tried the heart rate collector/monitor example pair (I have two dongles...
Hi folks,
We are in the process of evaluating nordic chips for our product.
One of the features we need is the ability to record an audio sound from an Ios app, send it...
Hello,
I have got nrf Power Profiler Kit for power consumption testing in our application board. I have a question regarding its output voltage for DUT devices. My application...
The project I am working on is to store the data acquired through BLE_uart_c and the data collected by the sensor on SDCard. I use FreeRTOS. The problem is described as follows...
Hello,
I have been developing a project and have run into an issue that I have been unable to resolve in the past two days. The code I have is in every way similar to other...
Hello,
I am using multiple custom boards with ISP1507-AX modules from InsightSIP, based on the nRF52 chip. I want to verify the revision numbers of the nrf52 chips inside...
Hi,
When libubsan and libasan is install the build systems enables some sanitize features in the compiler. These are trigger by the unit tests and four of them fail.
The...
Hi there!
It seems like I've accidentally destroyed LTE modem firmware in my nrf9160 DK during some experiments.
DFU update utility just can't flash the latest firmware...
Hi Nordic:
I just got some confused when I did development between mesh-sdk-2.2 and mesh-sdk-3.0 examples today.
And finally I find a steps to produce an issue of compatibility...
The project I am working on is to store the data acquired through BLE_uart_c and the data collected by the sensor on SDCard. I use FreeRTOS. The problem is described as follows...
Hello,
I have a device that use a NRF51822 with softdevice S110 V7.1.0 with the corresponding bootloader.
The new firmware I develop for this device is base on softdevice...
Hi,
I want to know which pin is signal input and which pin is signal out put for XL1 and XL2, XC1 and XC2.
The document just say they are analog inpu, no ohter introduction...
A cusomer wants to replace a serial communication with BLE. Host side is fixed with WL1837 Wifi-Bluetooth Module and Linux.
How can he implement the Nordic UART Example...
