I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
Hello,
I am currently implementing a security protocol from the IETF LAKE working group called EDHOC in Rust. I am using nRF5340dk and the bare-metal Rust examples from...
Hi there,
I am currently following this following tutorial on building a Matter setup.
When trying to build the openthread coprocessor I am hit with the following error...
I send and receive 1:1 using an ESB with nrf52840. I do not want to "use nrf_esb_start_tx()", but instead use PPI to trigger a specific event to be sent.
I want the PPI...
Hello
I am using nRF52833 based BE33 ( Celium Devices ) and using nRF52SDK17.0. Recently I have encountered the below issue:
err_code = app_timer_start(m_loadcell_timer_id...
I use 52833dK,Wpanctl whether there is a command to send custom data in the thread network.Similar to UDP in cli.
I found that there are relevant codes of HDLC software...
Hoping someone can help.
I am using an nRF52840 MDK USB dongle running nrf firmware in wireshark / nrf sniffer. I am attempting to sniff the bluetooth messages from my pool...
Hello,
I'm trying to get SPIM working with a nRF52840 DK, PCA10056.
I downloaded the nRF5 SDK 17.1.0 and I am able to build example projects, and I verified that I...
Hello,
Do you know where I could find a sample to read NFC Tag with Thingy91 ? The best could be to have a sample sendind on MQTT NFC tags reads.
I read different posts...
Hello, I need help to clarify an idea. What I want to do is get data from a Main board (Custom uC with sensors) via UART and connect it to the UART set pins (29 and 31) of...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056...
Hello,
I have a custom board using an nRF9160 chip. It connects to the Nordic Cloud. Modem firmware 1.3.1. SDK 1.6.1.
I have seen an issue 3 times now over ~6 months...
Hello, guys.
I have nRF51822 SoC running Zephyr OS. Among the other things, the nRF should communicate (over I2C) with the touch controller that will fire an interrupt every...
Hello,
I am using nRF52833 based BE33 ( Celium Devices ) and using nRF52SDK17.0.2. I am a beginner at Nordic. I want to understand how I can access a pin named " P1.04 ...
Hi,
I faced the exact problem nda , here . I take step just like nda did before. I unchecked "Enable debug options" as Marte Myrvold told, but still the same problem.
...
I am working with nRF connect SDK with nRF52840 dongle. I am compiling code using nRF coonect for VS code with nrf52840dongle_nrf52840 board.
For Programming nRF52840 dongle...
