Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Hi,
I have my custom board wired to the nRF52 development board. I am using SDK 15 and softdevice 132 for this. I am trying to set up SAADC to measure adc data on Analog...
Hi,
I'm only seeing the GPS_SIM driver in the nRF Connect SDK. Is there any driver to enable any evaluation of the nrf9160 on chip GPS anywhere?
Regards,
Kilian
Hello,
I have read numerous posts about NRF_ERROR_CONN_COUNT but yet able to solve this solve, my setup is NRF52840 Dongle as central and I want to connect to multiple Heart...
Hello all,
I am currently using the SoftDevice Handler library to enable/disable the SoftDevice and observe requests and state transitions on nrf52832 with SoftDevice S112...
I need maximum throughput in nrf52832. So i enabled DLE and using s132_nrf52_5.0.0_softdevice. The data packet length is 96 bytes in single packet. Conn interval 7.5 and 10ms...
I Can't set nRF5 SKD Root Path to: nRF5SDK=C:/nordic_semi/nRF5_SDK_15.2.0_9412b96/nRF5_SDK_15.2.0_9412b96
I created a global macro as instructed (many times) but the path...
Hi there!
I'm using nrf9160 DK's SiP to establish TLS connection to MQTT broker.
When I call nrf_inbuilt_key_write it returns 13 error code which means "If the operation...
Hi everyone.
In mesh light switch example., i try to add timer0 (or any timer).
After initialize timer, application always jump to timeout event, and i don't know why...
I am developing based on ble_app_uart example of SDK12 for nRF51 DK and I need to switch BLE off completely when power disappears to save battery and switch back on when power...
After reading the document for nRF52840 Radio Peripheral. I have a doubt about LENGTH field in packet format. what is the difference between LENGTH field and STATIC_PACKET_LENGTH...
Everything works fine if i use the default baudrate
NRF_UARTE_BAUDRATE_115200 but if i change it to 250000 or something higher the applications starts and goes directly...
Hello ,
I want to read around 6 analog pins, not necessarily simultaneously. I could afford some delay in between them. i am using nrf52832 dev kit with sdk 15. How do i...
http://developer.nordicsemi.com/nRF_Connect_SDK/doc/0.3.0/nrf/gs_programming.html#building-with-ses
I am following the example at the address below.
However, the following...
