Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Description : It is not possible to flash or debug an application with IAR on the Nordic target. This issue is caused by a bad interaction between CMSIS-DAP IF present on...
Having just upgraded to the Soft Device 6.0.0 and SDK 5.1.0, I can no longer flash my nRF51822 from Keil. I get this in the Keil console:
Load "C:\\Users\\Eliot\\dev\\nrf51_sdk...
Hi,
I'm designing a four layer flex PCB with the nRF51822-CFAC and recommended ST BAL-NRF02D3 balun and PCB trace antenna (not chip). I have a couple of questions.
...
Greetings,
Using the "central multilink" example project, how do I stop scanning if no advertisers are found? I see a case BLE_GAP_EVT_TIMEOUT in function on_ble_evt() but...
Hello
I found similar questions but no answer?
In the manual is written that I can control the parity bit in manual mode with the TXPARITY register but I can not find how...
what may be the reason for app_assert _callback error in s130,ble_central_and_peripheral that occurs from the following 2 lines
sd_softdevice_enable((uint32_t)NRF_CLOCK_LFCLKSRC_XTAL_75_PPM...
I have Rezence SDK working well with Keil uversion with wired and wireless debug without any issues on either nRF51 and nrf51822 DKs. When I port the project to Eclipse with...
Using the bootloader example code in SDK 8.1.0 for gcc, roughly how long does it take from power on to the call to bootloader_app_start()?
My device is motion activated...
Hi,
I have nrf51dk and analog EKG sensor. I know that ble_app_hrs allows to get R-R interval, but in my application i need to get also R-S and R-T intervals (or just R...
Hello,
I have combined two files spi_master and ble_app_uart into one file. Once trying to compile main.c compiles with no error but bsp.c compiles with 3 errors although...
Hi,
in S110 v 8.0.0, we can select the advertisement channels by setting the advertising parameters for sd_ble_gap_adv_start(..).
But what I want to do is to change...
Dear Nordic Team,
I am currently working on a project to develop firmware for S110 nRF51822 softdevice with the following requirements.
Read ASCII chars from a third...
i have found that
devzone.nordicsemi.com/.../
It seems impossible to connect two nrf51822,because soft device doesn't support the BLE Central role.But below said in...
I am getting an Error code on 8 on calling nrf_drv_gpiote_init() in my main() :
err_code = nrf_drv_gpiote_init();
APP_ERROR_CHECK(err_code);
Any idea what I am doing...
