Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Is there a function like battery_level_in_percent for AA battery?
I know battery_level_in_percent is only for CR2032.
Even though I compensate it to make it 3V from AA battery...
I have a question about Makefile template used in all samples in SDK12.x
What is the sense of:
$(foreach target, $(TARGETS), $(call define_target, $(target)))
-include...
Has anyone used a graphics library like emWin or TouchGfx on nRF52?
www.segger.com/emwin.html
http://touchgfx.com/en/
I do not see any posts on either forums or here...
Hello, I tried to implement the zephyr executing time functions API on my nrf52 hardware and I got the above error. According to my SoC documentation (nRF52833), this hardware...
Dear Devzone:
I am developing the design of a PCB that implements the nRF9160 SiP module, I have doubts about how to make the communication interface to connect the module...
Hello,
I used the nRF Connect plugin for VCS to create a Zephyr/BLE project. It appears this copies many files into the "build" directory which are required to compile the...
I am getting compilation errors when using the DT_ macros to access SPI bus child entries.
Overlay file:
&spi1 { compatible = "nordic,nrf-spim"; status = "okay"; sck-pin...
hardware : nRF52840DK-52840
SDK : NCSV1.7.1
IDE:Visual Studio Code
I wanted to printf float value , so I set CONFIG_CBPRINTF_FB_SUPPORT=y in my prj.conf file, my application...
Hello,
I'm using following code to read ADC values. The minimum sampling time I'm able to read the ADC reliably is 60ms. I want to lower it to say 5ms or 10ms.
Is there...
To the kind attention of Nordic support team,
reading at this: https://developer.nordicsemi.com/nRF_Connect_SDK/doc/1.8.0/nrfxlib/softdevice_controller/README.html#softdevice...
Hello,
I have I am trying out the LPN sample from nRF5 SDK for Mesh v5.0.0 and I have an issue where certain mesh configuration messages (e.g. set publication, add application...
Hi, We have custom nrf52840/33 peripherals, advertising every couple hours, and passing/receiving information from centrals running node.js version 12.22.5 with pc-ble-driver...
Hi, I work on custom board, which have NRF52833 and IS25LP016D SPI flash. I tried with SPI flash sample but SPI flash driver IS25LP016D was not found! err message show on...
Hello,
I want to use DTM FW for my design and have to update Tx & Rx pins to 21 and 20 respectively. Looking at the files in $\ncs\v1.8.0\nrf\samples\bluetooth\direct_test_mode...
Hi
I measured the CW output power of several DevBoards (nRF52832 and nRF52840) and the output power is much lower than expected.
Setup:
nRF52832 or nRF52840 DevBoard...
Hi Nordic,
when I run the samples/subsys/fs/fat_fs, the example of FAT file system usage with SDHC media, get error as below:
I have no idea how to fix it.
the SD...
Hello, sorry to disturb you I'm using Nrf52840 board and I would like to know how to flash correctly. I'm going to tell what i did with Visual Studio Code. I created a simple...
