Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
Hello
I am testing the nrf_GFX example with ST7735
but the example has a ST7735 128x 160 and i have St7735 80 x 160, I Change de dimentions in sdk_config.h
in the...
Hi, I'm a beginner for nrf52840 development.
As I know the ARM core operates on 64MHz clock.
So I think there is 64 MHz clock in this board.
My question is the...
Hello everyone,
I accidentaly flash the Dk when the power profiler kit was plug on it, so now the led are Always off on the PPK, to fix this I have to flash the PPK but...
hi support team,
i have one ticket about 53832 hardware problem that is resolved:
devzone.nordicsemi.com/.../52832-p0-25-and-p0-26-problem ,
Surprisingly i found out...
Hello,
I have this very strange issue where my code is hanging at startup while reading NRF_UICR->CUSTOMER register when build release code. system doesn't hang in debug...
When I enable and disable UARTE RX my chip consumes nearly 500 uA.
I assume the most of it comes from the "disabled" UARTE RX. Either im not disabling it correctly or thats...
Hello,
When we are trying to create mesh using IOS application latest version(3.2.0) but Mesh doesn't work properly.
But the same system is tested with Android Nrf App...
Hi
I am going through the AWS IoT example using an nRF9160 DK, but having some problems with it.
My setup
nRF9160 DK + LTE-M SIM card
I used this same board and...
Hi,
We are working on adding T-M to our middleware, and we discovered a pretty annoying side effect.
We are using NCS 2.0.0
One of our device is controlled using the...
Hi
According to Case ID: 279868 it seems like there has been some issues with modem lock up on nRF9160.
Some questions:
Do you know if this issue is still valid...
Hi there,
I am developing a central in nrf52840 dk using SDK v2.0.0 in VS code.
The BLE part is OK and it is possible me to get notifications.
Now, I need to store the...
Hi,
I have nrf52840-Dongle and nrf52833DK and it was working all good few days back with my code for BLE-UART (Centeral-nrf52840 Dongle and peripheral nrf52833DK) but now...
I need a crystal capacitor for this two Crystal XRCGB32M000F1H01R0 and SC20S-12.5PF20PPM. The value of this capacitor is 12pf and package 0402 So, please help for selection...
I am using a rotary encoder with nrf52840dk and I am confused about how to run sample QDEC code from zephyr/sample/sensor/qdec on nrf52840dk.
I got this error when i tried...
