VPN Solutions are a guaranteed private network association constructed on top of infrastructure that is publicly available. vpn connection free Providers provide an alternative...
Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
I stumbled upon Nordics video on facebook where they show how to calculate the distance between two NRF52840 Dev Kits. Link to video and article: devzone.nordicsemi.com/....
I downloaded version 15.2.0 of the nRF SDK. It contains the softdevice version 6.1.0.
I then attempted to upgrade to the softdevice to 6.1.1. After downloading the softdevice...
Hello,
What are the steps to recover a bricked nRF9160-DK? I want to get it back to the state that it was shipped in. I would assume refresh "secure_boot" and an app such...
Sir,
I have one custom MDBT50Q evaluation board and a ST-Link debugger. As the Keil IDE is fully defaulted to J-Link none of the example programs are building and flashing...
Hardware:Two nrf52840 DK Software: SDK15.2
We have 2 development boards acting as a master and slave communicating over UART. We are using the serial library for this application...
when i use the official example in nRF5_SDK_15.2.0_9412b96\examples\peripheral\blinky\pca10040e\mbr\iar using IAR IDE,
after building successfully, i failed to download...
Hi:
I use the new Mesh SDK 2.2.0 to make a demo.and I use the proxy_server and proxy_client example. now，I test and find the proxy_server example don't open the relay function...
Hi,
When I go through the code of light switch example, I am confused about relay functionality.
Compare with the v2.1.1, I can find the m_relay_enable in network.c but...
Hello!
We are currently developing a software solution which integrates many protocols into one Gateway. One of the protocols is Zigbee, and since it is the first time we...
I'm running FreeRTOS with SDK version 15.0 on nrf52 custom board.
I have two sensors, say A and B, on two separate SPIM bus instances. Sensor B utilizes PPI to trigger data...
I've been working on using an nRF52 as a host for a PS/2 synaptics touchpad mouse (to integrate with BLE HID). I was able to get a correct mouse position using two GPIO pins...
Hi,
i am using oled ssd1306 i2c with nrf51822. I am using peripheral mode and SDK v10.0. i choose this sdk version because of length i want to sent at one go that is 1024...
Help pls, i can't build a project.
Building ‘temp1’ from solution ‘temp1’ in configuration ‘Debug’ 1> Generating linker script ‘temp1.ld’ 1> Linking temp1.elf 1> Output...
Hi,
It seems that I have an issue with ZB_GET_OUT_BUF following the zb_zdo_node_desc_req example.
After several calls (around 10) of ProcessNodeDescReq , I can't get a...
I am using Linux (various breeds and hardware) and the nRF52840 Dongle. When I first plugged the dongle in it worked as expected
Then this
this is the output from dmesg...
