I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Is there a function like battery_level_in_percent for AA battery?
I know battery_level_in_percent is only for CR2032.
Even though I compensate it to make it 3V from AA battery...
When reading about access_opcode_t struct on its infocenter page it stumbled upon this table i don't understand.
access_opcode_t is defined as:
Data Fields
-------...
I'm employing 51822AA.
I need to debug firmware for this chip line by line. Like environment of ARM9 with Lauterbach TRACE32 through JTAG.
Is line debugging possible...
From application point of view, when should I use UICR and when should I use Flash storage? I have studied the documentation and the functionality seems very similar. The...
Hi everyone,
I trying to make a flash jump on Nrf51822 in my project. there are 2 programs(program A and program B) below. i am working on to make program A jump to program...
Hi everyone,
I'm new with nrf52832, and I need to measure elapsed time in microsecond between rising edges of 12 different Gpios. I have 12 piezoelectric sensors filtered...
Hi,
I have used nRF52840-PDK.
And I want to test profile and protocol with PTS.
I succeeded in GATT-based service test and GATT test with PTS.
But when I try to L2CAP...
How do you do
Now use the Nordic \ nRF5_SDK_12 2.0 _f012efa \ examples \ ble_peripheral \ ble_app_uart this plus Nordic \ nRF5_SDK_12 2.0 _f012efa \ examples \ peripheral...
I try to add default nRF sdk libs in Segger studio. All files exist and path corect.
in nutshell i try to add uart module to default ble_app_buttonless_dfu example
Hi ,
I'm looking for BLE Specification but I just found NRF52 Datasheet on Nodric page . Can you give me this document , It will help me a lot . Regards !!!
Hello All
I am planning interface the BLE peripheral + Capsence(Atmel QT111) board
i did the Capsence Board with Spi Protocol..then second phase i has to implement with...
Hello
I have some problem that I want to change Characteristic UUID different from Service UUID.
Like,
Service UUID : 11111111 - 1111 -1111 -1111 -111111111111
Charcteristic...
Hi Nordic,
I used FDS to operate updata to update data more than 10K once, but there was an error. Hint FDS_ERR_RECORD_TOO_LARGE.Can FDS operate more than 10K data at once...
I want to create own android app with just nus service (uart).I'm not very good in android programming, so there are two ways for me doing that:
Use Android-nRf-uart...
