Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
hello
1.NRF52840 Upgrade APP+BL+SD from SD15.3 to SD17.1.
2.BL use pca10056_s140_ble_debug,APP use ble_app_buttonless_dfu.
3.Program batch file.
nrfutil settings generate...
I have a case where a maximum of 1.4V will be applied to an GPIO pin immediately before the MCU powers up (the voltage enables a boost converter, which then powers up the...
I see this message on my debug output whenever I connect an app to my device. I'm trying to find where the opcodes and status is documented but can't. Can you please point...
Hi, I'm using a nrf5340 custom board. In my program I am using MCUBoot but I would like to know how I can remove the second slot in flash to flash a big program. I'm will...
I have 4 Thread end devices commissioned onto a matter network and want to control these devices from another Thread end device by pressing push buttons. Is this possible...
Hi,
I am having some issues with the Co AP Client and Server on n rf Connect SDK v 2 . 1 . 2 .
I have flashed two n rf 528 40 dev kits with the examples , one with the...
Hi,
I'm using the bare hci_uart example and try to rise the RTS line manually. Therefore I use the API
and added
in proj.conf. The resulting error code is...
As the title indicates, this question is regarding a scenario in which a coordinator needs to be replaced on an already established network. Is it possible to clone a coordinator...
I currently have a Thread network running using nRF52840 microcontrollers and another BLE network using ESP32 WROOM. I would like to connect two separate network using BLE...
Hello, I am working on a project that consists of sending Eddystone and ibeacon packets simultaneously, to begin with, I started by sending one package of each separately...
Below images detail given about VDD and VDDH in nRF52840_PS_v1.7 datasheet (5.3.1 Main supply) . According to this we can not connect both supplies simultaneously right?,...
Hi,
I'm a beginner to this kind of problem. I am trying to update firmware for nRF52832 through BLE using ESP32. I am using 17.1 SDK and Softdevice 7.2.0 with Keil.
I...
Hi,
I m trying to set up a LwM2M Client with Security Mode 2. I m using the LwM2M client utils and add some changes to the LwM2M Client sample.
In the function lwm2m_setup...
Testing UDP sample with sdk 1.7.0 I can't detect errors if the packet is not sent.
After a connection to networks and a few well-delivered packets, I put the device in a...
