here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
How do I power the nRF9161 DK with a battery? I have a spare 4.2V-3.7V lipo (2000mAh) but according to the docs, VIN ne eds 5V, so any recommendations for a compatible battery...
Hi Nordic Surpport,
Our product need to pass Certification, this certification requires "thermal resistance" of nRF52832-QFAA-R7, could you please provide this parameters...
hello：
In nrf5,the content of this struct variable can be easily modified to change the advertising data even during advertising,just like this:
ble_gap_adv_data_t m_adv_data...
Hi Nordic support:
Our product previously used nRF9160, all factory testing commands were included in one modem firmware. Now our product replaced nRF9160 with nRF9151...
I am running on bluetooth peripheral_uart demo with my nrf54l15 board and enable dfu feature so that it could upgrade firmware by using mobile app "nRF Connect", and it worked...
Hello, I have a custom board containing a module from Raytac with a Nordic nRF52840 microcontroller on it. The board also has a 32768kHz oscillator connected to the module...
Hi,
I am developing an android app on channel sounding using Bluetooth low energy. i want to send values from nrf52840 device to my android app, 1) How to send values from...
Since the nRF Connect extension for VS Code is buggy (at least in the latest version of VS Code), is there a guide available for setting up the VS Code IDE without using nRF...
hi:
There is an example of webusb next in Zephyr's latest Samples. I ran it with nrf52840 and encountered an error requesting the Microsoft operating system 2.0 descriptor...
Hello, I need some input on TX Power configuration for nRF5340+ nRF21540 .
(We are on NCS 2.7, and not yet migrated ot using sysbuild. Still using parent+child image....
Hello,
We're using the Scanner Compat (v1.6.0) library for Android in our app, and it has helped us tremendously.
Recently we've observed that the Xiaomi 12T has stopped...
I'm using SDK 12.3.0, and changed the TX_PIN to 30, RX_PIN to 5, flow control is set to false, bitrate no change(19200).After I programmed the firmware to my custom board...
I'm trying to test my nRF7002DK with aws_iot sample to see how it works. I'm following this guide however it fails during build configuration & never builds whatsoever. I...
Hi,
I have tested my BLE code and UART code separately, and both worked correctly during individual testing.
However, when integrating both, I encountered an issue with...
