This stopped working for me... Error is the following
Command failed: git ls-remote --tags --heads github.com/.../sdk-nrf
fatal: unable to access ' github.com/.../'...
Hello,
After a lot of efforts I managed to autoprovision and autoconfigure my nrf52840 board (provisioning and configuring inside the software and not through external app...
Hi there,
I am trying to interface at25xe321d with QSPI but it always end up returning zeros. Please find attached code and dts file for reference. Thanks Moh
Hi,
We have a custom PCB based on the nRF9151 and nRF7002 for a tracking use case, supporting both indoor (Wi-Fi scanning) and outdoor (GPS) positioning. Our firmware is...
When version 1.0.0 of nRF54L15-DK evaluation kit will be available and how to distinguish the version when ordered from distributors like Digikey?
In discussion here:
...
-> How to transfer data from one thingy52 device to another thingy52 device. If i have 2 thingy52 devices, I'll send data to 1st tingy52 then 1st thingy52 device will send...
Dear devzone，
Based on ncs2.9.1 and nRF54L-DK(v0.9.2), add in the prj.conf of the peripheral_uart example:
Compile and burn to nRF54L15-DK, the program does not run, and...
I have seen exaples using the Raytec MDBT 40 with ATMEGA32U4 infact adafruit has its own board with ATmega32u4 and MDBT 40.
Can I use MDBT 40 with ATMEGA328 ?
Thanks...
Hi,
I am facing issue on nRF51 s110 buttonless DFU. We are initiating DFU using nRF Connect and the device jumps from app to bootloader. On my Android Phone using nRF Connect...
hello,
i want to ask that is there any tool for reading and writing on flash directly.
e.g tool like extreme burner .i am loking for a tool like extreme burner.for nrf51822...
hello,
i am using ble_app_uart code and in this pwm is also used but when i am enabling pwm my bluetooth connection gets disconnected.
will you please tell me how to use...
I am a student and very new with your product and how to use it.
I just order nRF52840-PDK today via online electronic store.
Please provide complete equipment list...
Hi, I want to OOB pair two equal devices (pca10040 + NFC shield) via NFC. Since its not clear which of the two devices will act as NFC initiator (active) or tag (passive)...
Hi.
I'm trying to upgrade multiactivity_beacon scanner example to SDK 11.
But, there's no config for nrf52(pca10040) in that example.
So, I configured it myself and...
Hello,
I just purchased this device:
www.aliexpress.com/.../32399375500.html
but found out that evaluation board is only a debugger and does not actually program the...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
While investigating connection parameter handling, I noticed the following:
The is_conn_params_ok(ble_gap_conn_params_t * p_conn_params) function in ble_comm_params.c only...
Hello,
I am working with S132 3.1.0 on a project based on FreeRTOS. Under some circunstances I set manually the value of some characteristics by using the function sd_ble_gatts_value_set...
Hi,
I am working with a nRF51822 board and I want to program in OTA. I know how to program over the air, but the only problem is that when I have a new unused board I need...
Hi,
I am adding BLE functionality to one of my existing product. I product will play the central role for which I am thinking to use nRF51822 based module.
I learned...
