Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hi,
I'm trying to find an example of using the I2S audio interface with the Zephyr RTOS on the nRF52840dk_nRF52840 development board or on an nRF52840 device in general...
Hello ! I'm a beginner here, and I have a problem that I struggle to solve. A few years ago, a firmware was done by a company, for the one I work for. It was done with IAR...
Hi,
I am toggling a GPIO using the below code and trying to find out the relation of the frequency and the code statements. I know that GPIO peripheral is running at 16MHz...
Hi,
after fixing a missing ground in my setup (see devzone.nordicsemi.com/.../interaction-jlink-and-power-profiler-ppkii) I have not been able to get less than 50uA of idle...
My B0n bootloader (running on the network core) is trying to access XIP space and faulting. This is a part of an network core upgrade.
From what I can learn from the data...
Good evening,
I’m testing the SDK v17.1.0 “Open Bootloader with DFU” example. I’m using Segger Embedded Studio to program my Nano 33 BLE via the debug interface (P20) of...
Hello again Nordic World!
Yet another question about getting RSSI values:
Again, using 10028 and 10040 boards under sdk 12.3.
Is the adc acquisition of rssi done synchronously...
Dear DevZone,
within out project we make use of an esb communication between a nrf52840 DK connected to the PC via USB (a "station"), and a custom PCB with a nrf52840 micro...
Hi all,
We are developing an application using nRF52840 device and the idea is to enable the device with peripheral and central roles.
We would like to set two advertising...
Hi there,
We've been doing OTA DFU updates for a while now, but a recent increase (by one page = 4kb) of the firmware has created an issue.
Flashing through USB serial...
Hello,
I am using nrf9160 development kit. I need to use this dk with Modbus RTU master slave project. My question is does nrf9160 support for work on Modbus RTU master...
Hi Nordic,
I've reviewed the Mesh PyACI which uses a serial connection with a DK to provision a separate Mesh device over-the-air, if I understand correctly. But is there...
According https://www.nordicsemi.com/Products/Development-hardware/Nordic-Thingy-91/Download#infotabs
Version 1.2.7 seem to be the latest without "only for testing and development...
Hello,
I'm making an own service with a notify.
When I look at the bas service there is the following line to trigger the notifty:
Because I have serveral characteristics...
